2d boards from annotation to drafting

[MFT]

Good morning

I don't use drafting anymore, so I forgot some things.
I have to do a job to a client of putting into the table special facts with annotation, only that he then can open them with drafting.
The problem is that he doesn't feel the scale in the drafting step, if I make a 1:5 scaled annotation board and with cartiglio when the drafting load brings it back to me. There is a way to overcome the problem, in a few words you can do in annotation and load the drafting as if it were generated by the latter.

Thank you.

Mar

 

[Fabio_ff]

Good morning.

I usually do so (perhaps there are faster solutions):
once the draft is loaded, you write the scale_view command in the command line (when you charge an onnotation board in drafting, the drafting scale is carried on 1:1)
then enter value 1 to bring back the views to scale 1:1
then you ski all, or you select only the views that interest you.
at this point the geometry is scaled and you can replace the 1:1 scale of the drafting with that of the table.

Usually you have to move the views to get back the original table.

I hope you can serve me, a greeting.

fabio

 

[MFT]

Good morning.

I usually do so (perhaps there are faster solutions):
once the draft is loaded, you write the scale_view command in the command line (when you charge an onnotation board in drafting, the drafting scale is carried on 1:1)
then enter value 1 to bring back the views to scale 1:1
then you ski all, or you select only the views that interest you.
at this point the geometry is scaled and you can replace the 1:1 scale of the drafting with that of the table.

Usually you have to move the views to get back the original table.

I hope you can serve me, a greeting.

fabio

ok but quotas and texts remain small. I remember that in me10 it was drawn all 1:1 and then the cards in symbol and you chose the scale and the odds came accordingly. As you suggest, I climb the views but the odds remain with a small text height.
I hope to have explained I would like to recover the quotation made in annotation
Thank you.
Mar

 

[Fabio_ff]

ok but quotas and texts remain small. I remember that in me10 it was drawn all 1:1 and then the cards in symbol and you chose the scale and the odds came accordingly. As you suggest, I climb the views but the odds remain with a small text height.

here in fact only the texts remain small, the quotas adjust; But it is also a nuisance.

I hope to have explained I would like to recover the quotation made in annotation
Thank you.
Mar

I'm sorry.

fabio

 

[Er Presidente]

Good morning

I don't use drafting anymore, so I forgot some things.
I have to do a job to a client of putting into the table special facts with annotation, only that he then can open them with drafting.
The problem is that he doesn't feel the scale in the drafting step, if I make a 1:5 scaled annotation board and with cartiglio when the drafting load brings it back to me. There is a way to overcome the problem, in a few words you can do in annotation and load the drafting as if it were generated by the latter.

Thank you.

Mar

in me10 you must load the annotation module before loading the drawing.

 

[MFT]

in me10 you must load the annotation module before loading the drawing.

Thank you... it looks like what I needed, the president always knows more than the devil.

Mar

 

[MFT]

in me10 you must load the annotation module before loading the drawing.

I'm sorry, maybe I'm wrong. then I throw a table in full annotation we say in scale 1:5 then the load with drafting and he makes me see it normal if I go to take a quota but gives me a rescalated value of -5. if I make scale_view brings me back everything in scale but the quota texts remain small. it is not possible to have the design made with annotation loaded with drafting as if it were generated by drafting.
I remember that in me10 when I put the quotas he adjusted the size automatically according to the scale.
As my client gives me the 3d and I put it on the table only that then he would like to change them with drafting, I would like to avoid having to set them up again in drafting.
I hope I've been clear, so I do some evidence to see if I leave.
Thank you.
Mar

 

[Er Presidente]

to keep everything you have to edit the part before listing.
me10 (with the activated annotation module) recognizes the current view scale and makes you the correct quotation.
In fact, if you stay on the root, I will warn you that the altitude will be out of scale.

 

[MFT]

to keep everything you have to edit the part before listing.
me10 (with the activated annotation module) recognizes the current view scale and makes you the correct quotation.
In fact, if you stay on the root, I will warn you that the altitude will be out of scale.

perfect...... thank you again

Mar

 

[MFT]

always inherent in the topic it is possible not to view the message that from drafting to the opening of a drawing made with annotation.
in a few words the design notice made with the 3d you can not view it.
I would not like to let you know what opens the design that is generated with a 3d.
Thank you.

Mar

 

[Er Presidente]

always inherent in the topic it is possible not to view the message that from drafting to the opening of a drawing made with annotation.
in a few words the design notice made with the 3d you can not view it.
I would not like to let you know what opens the design that is generated with a 3d.
Thank you.

Mar

I think I do, but it's from the destination me10. If you want to extirpate the 2d by annotation there are two streets, a teacher with an option in annotation that I no longer remember: and another "draconian", carry out in dxf and reimport in me10. :smile:

Hi.