command creation asola

[ANGY80]

hello to all, I wanted to know if there is an application for inventor 2009 xp64 bit on the internet, for the automatic creation of an asola.
for example in the catia there is and is a command that uses in the sketch mode.
it would be convenient, without having to trace 2 circles, pull 2 tangent lines and cut the superfluous or draw a rectangle and go to radiate it for half the width of the asola.
thanks for the attention.

 

[Tarkus]

you can create the command by first downloading the macro relative to the sunbeds in: http://www.kwikmcad.com/icode/macros.asp.
then read this discussion on the forum:www.cad3d.it/forum1/showthread.php?t=9842&highlight=macro&page=2where in various passages, you can find directions on how to insert them into inventor through the vba editor...
p.s.
good for 2009 to 64 bit and also for 2010 always to 64

 

[ANGY80]

Thank you very much.

 

[pagnotz]

However, the easiest way to draw a sunshade in a sketch is not among those listed by you. . .
Just do, with the command line, first a line, then a first semicirculation (clicking and holding the mouse), then the second line and the second semicircumference. tangency constraints will be automatically put, so just quote diameter and length.

 

[Peppe]

I created an i-feature where I give width x length, and the insertion point is the central point....

 

[ANGY80]

a question to tarkus.
I did all the steps, I can't just make the macro appear in the command window to be able to insert it into the curtain previously created.

 

[Tarkus]

However, the easiest way to draw a sunshade in a sketch is not among those listed by you. . .
Just do, with the command line, first a line, then a first semicirculation (clicking and holding the mouse), then the second line and the second semicircumference. tangency constraints will be automatically put, so just quote diameter and length.

.

Right, but with the macro solve everything,quotes included with 4 clck 4....
It's not a big deal, but with the macro you make a little bit of time... .
It seems to me perhaps a small lack of inventor, not to have the command of asola under the button of the command circle; there is the ellipse, there could be the asola too.
They don't have to invent anything in acad for several years....

 

[Tarkus]

I created an i-feature where I give width x length, and the insertion point is the central point....

The postage was...

 

[Tarkus]

a question to tarkus.
I did all the steps, I can't just make the macro appear in the command window to be able to insert it into the curtain previously created.

I didn't understand what the curtain you created, so I'll tell you how I did:
provided that under tools->macro, your macro appears in the list; even after closing and rebooting inv... :
in sketchy environment (in ipt, not in iam):
-click with the dx in any area of the top command bar.
-personality
-commands
- here choose macro
-You should see an icon with the next namebround
-Translate icon on the sketch commands browser.
The game is done: the command of asola (obround) goes to be part of the sketch commands... .

 

[Peppe]

The postage was...

I press that you have to be in sheet metal environment, you create the sketch with the points - punch - and you choose asola (it would be useful to be able to place even the axes in the i-feature, but I did not succeed)
View attachment ASOLA.zip

 

[Tarkus]

I press that you have to be in sheet metal environment, you create the sketch with the points - punch - and you choose asola (it would be useful to be able to place even the axes in the i-feature, but I did not succeed)
View attachment 10187

thanks peppe... .