info dynamic blocks

[sgreender]

Hi.
I'm trying to combine two dynamic blocks, but I can see if it's possible or not.
reading online I tried some procedure but I still copy the visibility tables.

In the sense if the block to (the one in which I want to paste the other block) has n parameters and x states of visibility... nn gives me the possibility to paste the new block which also contains him xx states of visibility.
the glued block remains “dynamic” but only inside the block editor... but if I save and close nn I have the possibility to act externally on the visibility of the second block...
I know I've been a little twisted, possibly if someone replies, then I can detail better

thanks for the attention. Good day

 

[rpor66]

visibility states cannot be mixed, you can only manage one.

 

[sgreender]

So is it really feasible? I would also be fine in a single table of visibility, but also here I understand that there are functions, and I should reconstruct all the visibility in the block that collide...
It seems strange to me that by gluing it appears to me to the intent of the editor with his own tabaella of visible... in practice it glues me only the dynamic block inside the other block. so for the change of the visibility of the second block I should enter the editor blocks, change state and exit... but so doing the operation is repeated on all the blocks present in that page.

However, thanks to the feedback, if you have any advice, I agree.
Good Sunday

 

[lattu]

Can you attach the blocks? I would like to make an attempt

 

[sgreender]

Hi.
in the drawing you find two blocks.
to left the block in which I would like to paste n. times the block of dx making it maintain the possibility to select the type and the nr. of contact.
then if you need some details, write . thanks

 

[lattu]

I just figured out what you'd like to do and agree with rpor66.
nested visibility states do not work, they must be an integral part of the main block.
the possible ways are:
- create a single block that covers n times.
- operating with 2 separate blocks, the main is as enclosure and in the contact block insert the terminals and all attributes (of the single contact)

 

[sgreender]

Okay thank you, even though I didn't understand the two solutions you propose.. .
Basically I would need 2 "selecting states". . .
the first with which to choose the contact number to activate and the second (third, fourth etc.) for each contact that allows me to select the numbering. . .

or if you have suggestions to speed up the thing.. may also not have been of visibility but other functions. . .

 

[lattu]

the number of contacts you could manage with the serial parameter but then the visibility states would no longer work, for this reason I suggested 2 separate blocks or one that does not "container" that floods it as much as you want and maybe creates anchor points, the second block is the contact with the external lines to be extended and the attributes.
I prepare a draft dwg because it is only hard in words

 

[lattu]

Try to see if you like it

 

[sgreender]

Thank you!
In practice you suggest cmq to work with separate blocks, which is what I do practically. .
It's a good point, because I didn't use the anchors until now and I didn't think of the "container" question... in practice I usually create a complete block of a contact, restraints, clamps and I take the extensible edge, then take off from time to time the nr. of contact blocks I need. . .

other problem / slowdown always related to this type of blocks.

if I take a block that I set up with a certain visibility and copy it to another page this will change a bit at will.. or better if on the page where I go to paste it already exist other blocks so I seem that the block that I go to paste will reset.. .

 

[lattu]

Thank you!
In practice you suggest cmq to work with separate blocks, which is what I do practically. .

unfortunately as already said you can not manage everything with a single block

other problem / slowdown always related to this type of blocks.

if I take a block that I set up with a certain visibility and copy it to another page this will change a bit at will.. or better if on the page where I go to paste it already exist other blocks so I seem that the block that I go to paste will reset.. .

Did you try to glue it as a lock and then explode it? should keep the same settings

 

[sgreender]

depends on cases. but I have never looked into it properly... more than anything else I have always done a little bit to try and I know that I have some setting of the various fields packed during the creation of blocks

 

[prismacad]

I had analyzed such a problem at the time.
see if it can be useful for your block.

Blocco con controllo dinamico

Buongiorno a tutti! Da molto lavoro con i blocchi dinamici, però oggi mi sono imbattuto in una funzione che non mi ero mai accorto che ci fosse e a cosa servisse...ovvero il controllo dinamico...in poche parole guardate qua: qua il dwg: questo anche...

www.cad3d.it

 

[sgreender]

I had analyzed such a problem at the time.
see if it can be useful for your block.

Blocco con controllo dinamico

Buongiorno a tutti! Da molto lavoro con i blocchi dinamici, però oggi mi sono imbattuto in una funzione che non mi ero mai accorto che ci fosse e a cosa servisse...ovvero il controllo dinamico...in poche parole guardate qua: qua il dwg: questo anche...

www.cad3d.it

as soon as I have a moment I study, but I have already opened the dwg of example circle-triangle and I vien to think that I could manage with visibility the nr. of contacts that I want to activate and with dynamic control I manage the type of contact and its numbering... That sounds great, but I have to try.
Thank you!

 

[sgreender]

with dynamic control but I can't set the text that I want an attribute... Am I wrong?

type what you can do with the block properties table

 

[sgreender]

I add. . .
I had discarded the table of the properties because in that case the attribute remains editable, so I had passed to the states of visibility inserting nnn texts for the various numberings of the contact (various states), plus a modifiable attribute that appears only in a certain state (and disappear all other texts "fixes").

 

[sgreender]

Excuse me if I rekindle here... but in reference to the last mex, do you have any idea if you can block an attribute so that in the nn block is editable?
that as I said above using the table I can vary a text depending on the status of visibility (for example) but my problem that so doing the block takes the correct text, but in turn this remains editable