post secmus5 problem

[francescozeva]

Hello, I have a problem in processing 4 ax programs on a secmu with s5 control.
In this case the post processor only recognizes me the work plans 0 90 180 but not the 270 .
and they recognize them only if I put them 0 floor over 90 floor facing 180 floor below then as logic I tried to put the plan behind but without result.
I tried with all other plans (right left even iso but nothing).
Could someone help me?
I know a little post processors and I tried to get our hands but without result.
Also because I don't know if the problem comes from the fact that the cam doesn't recognize me as plan 270 or post processor.
on another secmu but siemens plans recognize me all.
Thank you for your help.

 

[marcofor]

with mastercam you need to create a plan using the wheel command planes at 270° because the back plane corresponds to the rotation on the axis b I usually create all the plans trenite rotation of the plane just to not have such accidents the post if it is configured for the 4 axis suppresses the other rotations.

 

[francescozeva]

How do you use the wheel command?
I never used it to make him recognize the plans, use the transla 3d!!

 

[mauro1974]

Hi.
I have a post of a secmu made by me if you want to send it to you but I don't know how....

 

[mauro1974]

I understand I attached my post to prove it. . .
Good job

 

[marcofor]

How do you use the wheel command?
I never used it to make him recognize the plans, use the transla 3d!!

then in mastercam x you have the possibility to manage the wcs (machine origin) and the construction plans of the geometry, below you should have the writing (plan) if you click on it opens a drop-down menu with the possibility to create the plans that you need at this point generate the plans through the rotation command and perform the processing while keeping the wcs reset of the machine changing only the processing plans, if the post is configured to duty.

 

[francescozeva]

I'm just importing dxf files I find myself on the top floor and I'm going to do what you explained to me, I'm putting the geometries I need on the floors I need, and for a car I use that has a dedicated post works very well.
on another secmu that uses a siemens control does not work a great deal, but at least I can get a source for every plan so that I convert the origins with the coordinates a and b that will serve me, instead for this secmu s5 the problem I think it is that, that the post is not properly configured, and for this reason it does not detect all plans.
cmq is now I will try to use the post sent to me by mauro we hope it works .
Another thing, I would like to be able to work this way but directly from solid models, I tried but on a solid model to go to take the chains then it becomes complicated, then I returned to the old methods by putting all the 2d geometries that I need on the planes, someone does differently? Thank you all! !
(Chuckles)

 

[francescozeva]

cavolo io da sto post non ci capisco una mazzzza

dopo ho inserito come esce il linguaggio del mio postho inserito anche

%g04tt5 ( t )
(dis= t )
(des= mod= )
(tempo stimato di esecuzione pezzo
g25xyzg37ol
oum
g00u0g28ug29u
ovm
v0 g28vg29v
t96m06
g25xyzg43z
ox1oy1oz1
!:rox*=am;am=am+1380;:wox*=am!
!:roy*=bm;bm=bm-730;:woy*=bm!
hr30ht.9ha-10hc200
m93
s500m3
g4tt2
m19s0
ox1oy1oz1
g0x0y0
z<ha>
g61x<hr-bn+ht>dm35
!ifam>99000;gon8001!di=am!
g0x0
g4tt2
m19s180
g61x<-hr+bp-ht>
!ifam>99000;gon8001!di=(di+am)/2!
g0x<di>
g4tt2
m19s270
g61y<hr-ap+ht>
!ifam>99000;gon8001!dj=bm!
g0y0
g4tt2
m19s90
g61y<-hr+an-ht>
!ifam>99000;gon8001!dj=(dj+bm)/2!
!:rox*=am;am=am+di;:wox*=am!
!:roy*=bm;bm=bm+dj;:woy*=bm!
g0x0y0


t%
g25xyz g37ol
oxaoyaozaoba
t229 m6 ( fresa piatta | diam. - 20 | 20. flat endmill )
t229m75
m59
g0g28bb0g29b
m42
n229g0x20y-68.819m3s3500f50
z25
z5
g1z0f25
y-48.819f50
g3x0y-28.819i0j-48.819
g1x-16.246
g2x-26.246y-18.819i-16.246j-18.819
g1y18.819
g2x-16.246y28.819i-16.246j18.819
g1x16.246
g2x26.246y18.819i16.246j18.819
g1y-18.819
g2x16.246y-28.819i16.246j-18.819
g1x0
g3x-20y-48.819i0j-48.819
g1y-68.819
g0z25
g0g28bb90g29b
x20y-50z43.819
z23.819
g1z18.819f25
y-30f50
g3x0y-10i0j-30
g1x-16.246
z-18.819
g2x-16.246y10i-16.246j0
g1x16.246
z18.819
g2x16.246y-10i16.246j0
g1x0
g3x-20y-30i0j-30
g1y-50
g0z43.819
m9
m02
s
xa=0
ya=0
za=0
ba=0</hr-ap+ht></di></hr-bn+ht></ha>

 

[francescozeva]

cavolo io da sto post non ci capisco una mazzzza

dopo ho inserito come esce il linguaggio del mio post

%g04tt5 ( t )
(dis= t )
(des= mod= )
(tempo stimato di esecuzione pezzo
g25xyzg37ol
oum
g00u0g28ug29u
ovm
v0 g28vg29v
t96m06
g25xyzg43z
ox1oy1oz1
!:rox*=am;am=am+1380;:wox*=am!
!:roy*=bm;bm=bm-730;:woy*=bm!
hr30ht.9ha-10hc200
m93
s500m3
g4tt2
m19s0
ox1oy1oz1
g0x0y0
z<ha>
g61x<hr-bn+ht>dm35
!ifam>99000;gon8001!di=am!
g0x0
g4tt2
m19s180
g61x<-hr+bp-ht>
!ifam>99000;gon8001!di=(di+am)/2!
g0x<di>
g4tt2
m19s270
g61y<hr-ap+ht>
!ifam>99000;gon8001!dj=bm!
g0y0
g4tt2
m19s90
g61y<-hr+an-ht>
!ifam>99000;gon8001!dj=(dj+bm)/2!
!:rox*=am;am=am+di;:wox*=am!
!:roy*=bm;bm=bm+dj;:woy*=bm!
g0x0y0


t%
g25xyz g37ol
oxaoyaozaoba
t229 m6 ( fresa piatta | diam. - 20 | 20. flat endmill )
t229m75
m59
g0g28bb0g29b
m42
n229g0x20y-68.819m3s3500f50
z25
z5
g1z0f25
y-48.819f50
g3x0y-28.819i0j-48.819
g1x-16.246
g2x-26.246y-18.819i-16.246j-18.819
g1y18.819
g2x-16.246y28.819i-16.246j18.819
g1x16.246
g2x26.246y18.819i16.246j18.819
g1y-18.819
g2x16.246y-28.819i16.246j-18.819
g1x0
g3x-20y-48.819i0j-48.819
g1y-68.819
g0z25
g0g28bb90g29b
x20y-50z43.819
z23.819
g1z18.819f25
y-30f50
g3x0y-10i0j-30
g1x-16.246
z-18.819
g2x-16.246y10i-16.246j0
g1x16.246
z18.819
g2x16.246y-10i16.246j0
g1x0
g3x-20y-30i0j-30
g1y-50
g0z43.819
m9
m02
s
xa=0
ya=0
za=0
ba=0</hr-ap+ht></di></hr-bn+ht></ha>

 

[mauro1974]

ok it is all right if you have the control san giorgio system 15 the first part concerns a cycle of tasting with renishaw that you can turn off if you want to turn the post, for the rest it is ok what goes out ......apart from that n° turns are to 0 and other things that are missing.... it works. . .
Hello! ! !