replace the axieme used in the table

[reggio]

hi, imagine you have set up the table with the various personalized views the magnifiers, sections, etc...

now you have been asked for a very small change (that you have done saving apart the assemblies and parts without using the configurations... sob)
Now can I go to the table and replace the first aid with the new one?


....or at least, can you set the same current view to the axieme and then in the table?

 

[Mike1967]

hi, imagine you have set up the table with the various personalized views the magnifiers, sections, etc...

now you have been asked for a very small change (that you have done saving apart the assemblies and parts without using the configurations... sob)
Now can I go to the table and replace the first aid with the new one?


....or at least, can you set the same current view to the axieme and then in the table?

next time, run a pack and go starting from the drawing, logically
put in prefix or suffix to identify the new design group/axis/parts, I put a n° revision.
so doing you will have all the drawing/axis/parts related to each other.

to the point where you are now it is best to rename the set you put on the table and use the old name to save the new set by name (sit "save as a copy").
Make sure the various parts are related to this new set.
once the design is opened, you should have the table of the new set.
I strongly advise you to make a copy of the whole old-age folder before doing everything, they are operations that can bring disasters, but if done well
They work.

 

[reggio]

I'm sorry.

 

[Mike1967]

I'm sorry.

How'd it go?

 

[Mario SJPD]

If I am not mistaken with solidworks there is the possibility to go to change the references of a table by associating the same with another set.
Once you make a copy of the table in the opening window at the bottom right there must be something to open that gives you the references of the table in the same window you can change them.
Sorry the explanation pressesapochism but you know jumping from one program to another.. .

 

[Poly]

is right bass band: in the open command dialog box there is the reference button that allows you to change the files that are used for a table but also for a set. therefore it should be enough to duplicate the table and in one of the two to change the references to point to the old together.

 

[Mike1967]

instead I prefer to do everything in manual, in fact I noticed the name
of the set that gives the name also to the drawing file, is not updated
creating not few problems.
in practice it is true that the design is referred to the new set, but the name
that I put in automatic is of the old together.
Maybe I'm wrong, but after some disaster I stopped using that.
procedure.
It doesn't seem logical that the name in the drawing file is not updated
with the new name of the new team. ($prp:"sw-file name(file name)") per capirci...

 

[Poly]

I also use that property in the cartouche. never happened to me that it did not update... the names of the assemblies and parts for us are encoded and reflect the codes and versions of the analogue articles. I used the procedure a few times to recover some sort of rejuvenation mistake. If he hadn't updated, it would have been a disaster.

 

[Mike1967]

I also use that property in the cartouche. never happened to me that it did not update... the names of the assemblies and parts for us are encoded and reflect the codes and versions of the analogue articles. I used the procedure a few times to recover some sort of rejuvenation mistake. If he hadn't updated, it would have been a disaster.

Since I always consider what others say, I have examined well
my design model and trying various settings I noticed
that there was a mistake in setting the properties.
in practice now, set as from attached image, to the replacement of
references also updates my name.
thanks poly, you never end up learning.:finger:

 

[Mike1967]

Since I always consider what others say, I have examined well
my design model and trying various settings I noticed
that there was a mistake in setting the properties.
in practice now, set as from attached image, to the replacement of
references also updates my name.
thanks poly, you never end up learning.:finger:

But when I go to save there's still the old name...azz