subprograms with topsolid

[da23do]

hello to all, I use just top solid cam, I have a problem with long files.. .
someone knows where I can activate the subprogram option, like m98- m198. for servers outside the machine can read so many fast blocks?
Thank you all!

 

[SoluzioneTOP]

Hi.

I am sore but I think that subprograms are not managed by internal topsolid commands but by a particular post-processor configuration and that is not always possible.

I believe you should contact the programmer who compiled it:finger:

 

[da23do]

I found the system, in operation management, in the processing that serves to put in m98 or m198 that is, next to pp: you have to write y_to_c in case you work in x-c with g112 g113. or y_to_c spg in case you work in x-y. I think that the latter also applies to 3-4 or 5 axes. 3 safe.

 

[SoluzioneTOP]

absolutely not ....the ppword y_to_c is nothing but a call for a procedure already preconfigured in the post-processor expressly valid for lathes with axis c and in addition it is not said that this applies for any control....so I suggest you try the command but read well the iso that vien out before you throw it in the car

 

[da23do]

Well I can't tell you if it was expressly preconfigured for the lathe on which I work, (moriseiki nt 4250) but I tried it and I can guarantee that it works perfectly!
Pull down the position of the axle, turn. fast pos. and then the m198p1000 with consequent final release. and at the time of the post processor takes out the normal program and in addition the sub program apart. es: o0001 and o1000 in two separate files.
if there were more than one such thing goes on with o1001 1002 1003 etc. the good thing is that in the cases of g112-g113 I have seen that the fast placements do them in g1 with very high gears type f10000. What machines do you work on? Are you okay with topsolid? I have some problems. type the ripass on segment, levels, seams, and machining of gorges a little particular... I am dabbling to draw toptool tools but I still have a lot of road.... Hi.

 

[SoluzioneTOP]

moriseiki nt 4250...certain that goes...and this does not mean that there is no preconfiguration in the pp I mentioned to you

try to make a 3.4 or 5assi cilcus on a milling center with similar or different control. ..it would only mess because not implemented in the pp

With ts I feel good... I'm not complaining, of course a life without problems would be a great boredom, would you? :

 

[da23do]

Unfortunately I have pp for cutters... just to come back... 6 between okuma biglia and mori. nothing... cmq is troubled better to have but not too much from... When you're at first arms like I wouldn't mind finding the square in a short time... in the company from me use visi cam for friezes... even if I hope one day they also buy post for milling. . .

 

[lorenzorll1962]

hi, I am of vercelli, use topsolid since 2005 to program a fresa lathe with y axis, now I am using topsolid veraone .69 and I find it is a great program, only sin that the post is almost armored to any modification, unlike mastercam (I also use it).
unfortunately in my company have bet on mastercam x

 

[da23do]

Well, it's a problem that I didn't do because I don't even know where to put my hands... cmq is really great... However it is a sbattone to configure at least initially... to be able to pull down safe programs.... also you go back busy? What car?

 

[lorenzorll1962]

with topsolid programmo a lathe heyliegenstadt heynumat 35 with axis y.
sim is true, it is quite complex to configure and set, you never finished learning

 

[da23do]

azz!!! and I think I work on a big car!!! is a beast!!! Who knows how anxious the tape tests!! and so you have the license and pp only for that machine?