videotutorial in italiano vectorworks

[zetadierre]

Good morning

I started making videotutorial about the basic use of vectorworks

I started from the beginning, so for now there is little

to whom I serve the link in signature

 

[Marcogeo]

......... I will then review the tutorials. cmq compliments for the will.

 

[giùgiù]

Big Unclerip! You are among my "bookmarks"
elementary schools are the most important schools, and build good foundations of any matter as well. So you took a big responsibility with who like me is a newbie of vectorworks... said this, having already disabled the zoom with the wheel , wait anxious new lessons!

Thanks :finger:

 

[zetadierre]

Big Unclerip! You are among my "bookmarks"
elementary schools are the most important schools, and build good foundations of any matter as well. So you took a big responsibility with who like me is a newbie of vectorworks... said this, having already disabled the zoom with the wheel , wait anxious new lessons!

Thanks :finger:

Please! I'm very pleased.

I am zetadierre! Unclerip is the creator of the site! :smile:

 

[giùgiù]

Please! I'm very pleased.

I am zetadierre! Unclerip is the creator of the site! :smile:

you are right zetadierre, I noticed later but I couldn't change the post, how can you change? must be senior member?

 

[zetadierre]

you are right zetadierre, I noticed later but I couldn't change the post, how can you change? must be senior member?

no change only a short time after you wrote the message, but no problem!

If you study those 5 lessons you have a basic knowledge package to begin with, in theory enough, obviously accompanied with a little practice

 

[giùgiù]

are already at work, thanks:finger:

for your knowledge I have done university exams using microstation, thinkdesign, illustrator, cinema 4d and photoshop, now it's up to vectorworks but I strongly hope it's the final and final of the list, it really takes a long time to get familiar with a software... ah perhaps it will be necessary to learn autocad now that "it" came out for mac.
:biggrin:

 

[zetadierre]

online the lesson: realization of a house in canadà_model setting and walls

see the link in signature

 

[zetadierre]

online la vii lesson: realization of a house in canadà_solve setting

see the link in signature

 

[Tommybussy]

Mr Zetadierre,

is it always possible to have the links of the videos created by you? ? ?

distinguished greetings

 

[zetadierre]

Mr Zetadierre,

is it always possible to have the links of the videos created by you? ? ?

distinguished greetings

Hello Mr. Tommybussy

can search on youtube through "tutorial vectorworks ita" and will see my tutorials. at the moment various contingencies make the project stop, although I hope we will soon have good new.

good vision and greet me his magnificent land, which I always remember with extreme pleasure

 

[sofly90]

I'm sorry where I find the explanation videos? ? I just signed up and I don't know how to move!!! I use it for a few months vectorworks but now I have a problem in the realization of a ceiling with exposed beams :s and I am in total panic! ! !

 

[zetadierre]

I'm sorry where I find the explanation videos? ? I just signed up and I don't know how to move!!! I use it for a few months vectorworks but now I have a problem in the realization of a ceiling with exposed beams :s and I am in total panic! ! !

calm and cold blood. at the moment there are the old tutorials you find on youtube as it is written above. If you have problems on certain topics, then open a thread with pictures maybe and let's help you

 

[Ramaja]

It's a shame you stopped with the video. I understand you were contacted by videocom. Let's just hope that the project goes on and that your interesting lessons continue to go out.
Can you tell us when there are new ones?

 

[zetadierre]

It's a shame you stopped with the video. I understand you were contacted by videocom. Let's just hope that the project goes on and that your interesting lessons continue to go out.
Can you tell us when there are new ones?

If it happens, I won't miss it. thank you very much for the compliments

 

[Ramaja]

then I immediately start asking you some clarification on the vw, lesson 7 house in canadà:
in the lesson you talk about the need to create a glossy "solar 0" to avoid that the loft in question is not paralyzed to the masonry above.
what are the characteristics of this piano-solar? is the glossy at the same height as the masonry or is it in the interquota between the two floors? (i.e. between +0 and -30)
type, considering a first floor: ground floor with walls 2.70 from the ground level. altitude-solar1 +30cm (then from 2,70 to 3 m) and therefore first floor (from 3m to 5,75). Or did I get it wrong?

in my case I am trying to insert in vw a state of fact a little peculiar with the quota floor 1 to +61cm, a garage at the altitude +0 (outside the perimeter of the building), a basement that goes down from +31 to -131. and floor between basement and ground floor of 30cm in brick, how many "lights" vectorworks should I create to have a good 3d model?
and if I want to get a decent rendering of the facade or a prospect, how do I prevent the loft from despairing the wall continuity since you have extended the boundaries of your loft to the outer perimeter of the house?

I hope I can explain myself and you can help me.

I have "tented" to understand something from the manual but it seems written to create doubts instead of to help.

 

[zetadierre]

You should, if it's not a problem, open a thread with the specific topic... Otherwise you get confused and other people who might have your own problem would make it difficult to find the topic.

What version of vw do you have? See you in the thread

 

[Ramaja]

You should, if it's not a problem, open a thread with the specific topic... Otherwise you get confused and other people who might have your own problem would make it difficult to find the topic.

What version of vw do you have? See you in the thread

provvedo: al momento ho la 2012 architect con renderworks

 

[morpheo_9]

Hi, I'll meet you now.
I am an industrial design student in florence.
Just like you zeta, I've been passionate about vector when I joined the university. I am now preparing the argument but I miss some fines I have not yet acquired.
I have created an object 3d. I have vain the relative viewports of the views but now as the quoto? because if I enter the viewport and quoto I show them in every view, but if I quoto externally I miss the scale. Can you help me?
thanks in advance

 

[lory.b]

I have created an object 3d. I have vain the relative viewports of the views but now as the quoto? because if I enter the viewport and quoto I show them in every view, but if I quoto externally I miss the scale. Can you help me?
thanks in advance

Hi.
you must quote in the annotation space.
when you edit a viewport (double click) or, even better, click on the viewport with the right-click, it appears among the voices of the context menu editing annotations. enter this mode and quoti.
I do.