of the holes and their adaptive projection:)

[themole]

hello to all problem:

I run holes on a set in correspondence of 2 combing parts but opening the single part I do not see the newly created hole.
Does anyone help me? Thank you.

 

[eugenesis]

. Sorry, but I don't see the problem.
If you use inventor 2016 or an old version, the thing is equal;
work together is managed within the assembly where you created them;
have never altered the individual parts which remain unaltered;
If you want to drill two parts in correspondence, punch one and then in the other, take the first references
with or without adactivity as it is always done

Hi.

 

[themole]

I drilled one on the side but how do you get references in the other? I am acerbo for a long time.thanks

 

[eugenesis]

. I'm sorry, but do the classes?
Is it money thrown away??
the time you lose your evidence on your own maybe to get some pocci ..
Isn't that a cost?
you are asking the abc of how to use inventor .. excuse , but if I give you the solution to this problem (project geometry
After two minutes you'll be back in charge!
think that there are software-houses that refuse to provide you with the products if you don't do the courses for benign!!
It's like a car dealer when you go get a new car, you don't give it to yourself if you don't have a license...
But you're getting out of the dealer's salon, it seems to me without my driver's license, but I don't think you'd go so far!
I'm sorry I'm direct! http://www.cad3d.it/forum1/images/icons/icon6.png

 

[themole]

Maybe I didn't explain well.I have already projected and created holes from the axieme on the not yet perforated part to create coupling rivets but saving and going in the newly drilled part do not appear the holes

 

[GianniM]

Hi.
try to replace the hole command. use the axitant design and create a bolt with hole. If you don't want the bolt, you can pick it up in the design menu. You will see that in this way the hole appears in the parts.

:36_1_11:

p.
The title of the discussion is a little too generic in my opinion. If you can change it.

 

[Tarkus]

if you make holes with working in the environment together I will not rite them on the part.
the logic is this:
I create more parts than I'll actually have to pierce once I'm paired.
It is normal that the drilling part remains without holes.
If you want to match the holes from one side to another using the joint positioning, you have to do this:
part a with holes, bound together with part b to drill.
together, double click on the part to be drilled,(b.: the file of part b non must be open)
the aid prepares itself in modality and shows you the normal controls of the environment part.
create a sketch on the face/floor where you want to make holes on the part to drill.
proceed in the normal way as if you were in the environment part:
project the holes geometries already present on the part a and then make holes on the part b.
once the holes are done, right click in the graphic window -> ends edit-> save.
At this point, if you open the ipt file of part b, you will find the holes already made.

@eugenesis:
When did the courses explain it to you or is there perhaps a faster method?

 

[eugenesis]

your explanation tarkus is done very well and very clear, contrary to the questions asked ..
(if you do not want it ..premi ctrl).

You think maybe I've been a little "fucky" talking about classes???
However I tell you that the courses have made me experienced people who + experts can not ..
I didn't know if I explained (he said the parachute. . ).

 

[Tarkus]

your explanation tarkus is done very well and very clear, contrary to the questions asked ..
(if you do not want it ..premi ctrl).

You think maybe I've been a little "fucky" talking about classes???
However I tell you that the courses have made me experienced people who + experts can not ..
I didn't know if I explained (he said the parachute. . ).

no, no, my age is not a captious question, I really wonder, since I am self-taught and did not take courses, if there is a faster and more direct method of what I have exposed... .
I didn't even put the problem....:wink:

 

[GianniM]

I'm a student. I can't do that. They cost too much. But if I introduce myself to the company and I say I don't know how to use programs fall back on you. I'm told they're going after you even at the unit if I go.
and then learn "smantling", talking between friends and the things you find on the internet like this forum.

On the other hand, if everyone did courses, a forum like this would hardly serve anything. I'm going to raise the horn, pay an instructor, who immediately solves everything.

then I understand that instructors hate users who help other users free of charge.