align objects to ucs together

[Newplasman]

good day and thanks to those who make available to all their experience, making the life of those who make modeling 3d, better :4441:
work with inventor 2010.
I have created some oggets, some starting from ipt, others within a set, in overalls the uucs is aligned to the main dimensions as when I had created them.I do not know how, now all the axieme is slightly rotated on ́the ucs.
exists the way, align the rotation exactly on the ucts together?
Thank you!

 

[Tarkus]

work with inventor 2010.
I have created some oggets, some starting from ipt, others within a set, in overalls the uucs is aligned to the main dimensions as when I had created them.I do not know how, now all the axieme is slightly rotated on ́the ucs.
exists the way, align the rotation exactly on the ucts together?
Thank you!

Is the first item you put together always fixed or not?
However it is:
-dx in the browser on the component;
- Cut out the "fixed" check.
-win the object to the plans of origin
- resign the "fixed"
- if you think you're taking off the constraints above.

good day and thanks to those who make available to all their experience, making the life of those who make modeling 3d, better!

:36_1_11:just as saints at once !!!:36_1_18:

 

[pagatti]

Thanks tarkus,
I forgot to say that I have the English version, and going with the dx on the component, I can put or remove the "grounded" check, but I can't grasp anything that translated is "wine to the plans of origin". Do you have any ideas? I tried them all, but I couldn't. . .

to bind to the plans of origin I think it is meant: ipt xy plan aligned to global xy plan, xz allinaetao with global xz and yz of the ipt aligned to global yz. . .

However inv2011 also has, in the constraints, the tab "constraint set" that allows to align 2 ucs...
the problem is that I can't generate these ucs....

 

[Newplasman]

Thank you tarkus!
I'll buy you a beer!

 

[Newplasman]

thanks to you, too, in fact it was so, I had the lighting a moment after sending the message. beer for you too!

 

[Ilario]

small tips with the same result but less click:
select the component to be fixed at the origin -> ribbon bar tab "assembly" zone "production" -> expand the only command that shows you and from the list choose "fix and set component as root"

 

[pagatti]

small tips with the same result but less click:
select the component to be fixed at the origin -> ribbon bar tab "assembly" zone "production" -> expand the only command that shows you and from the list choose "fix and set component as root"

Maybe I'm a little out of the subject. . .
but the discussion gives me a point... I learned about inv11, now with inv2011
I find this tab of constraints that binds two ucs between them.
to me this would serve a lot, the problem is:
How do you use this command? asks me two ucs but I don't know how to create them
n.b. : inv 2011 is in English (which gives me no problem), but I do not use ribbons but classical display to save memory, and therefore this ribbon does not exist

 

[Ilario]

It's a long time I use the ribbon, so at spanne the command I said before should be in the top command bar by clicking the brake should give you a menu with voices, these entries are additional commands. must be in one of these series of commands.

constrain set I don't know him... I look at you

 

[Ilario]

I have inventor in Italian, but what you call "constrain set" is always close to constraints and has an icon similar to tetris? to understand.. .

 

[pagatti]

I have inventor in Italian, but what you call "constrain set" is always close to constraints and has an icon similar to tetris? to understand.. .

the icon are two close xyz triads, and it is easy to understand how it works. . .

the problem is to create the ucs, I found the command, but it doesn't work as the guide says, I should be able to bind the new ucs to the edges of the pieces, instead I can't...

 

[Ilario]

I understand...

create the ucts in the part with the ucs command, select the origin point of the ucts, then you have to select another point that gives direction to the x axis and another point that gives direction to the y axis, done.
now you can use the constrain set

 

[pagatti]

I understand...

create the ucts in the part with the ucs command, select the origin point of the ucts, then you have to select another point that gives direction to the x axis and another point that gives direction to the y axis, done.
now you can use the constrain set

how do you select the source point?
I attach an image that shows what appears with the ucs command.
the problem is that I can't select anything, neither in the graphic window nor in the tree....

 

[Ilario]

you have to select a top of the piece. But you are together, then I don't think you can bind the bird of the asses. .

 

[Tarkus]

Thank you tarkus!
I'll buy you a beer!

I like that blonde beer.
if I pass from the weaning, besides beer, of blonde there would also be another famous local product ... :36_1_18::4404:

 

[Newplasman]

I like that blonde beer.
if I pass from the weaning, besides beer, of blonde there would also be another famous local product ... :36_1_18::4404:

you bring a retino, then the language directions and where to go I give it to you!where you gigi turns there is full....to become weird!:36_1_5: what a life!