autodesk inventor certification

[r-miky-b]

Good morning, everyone!
I am new in the forum, I presented myself in the appropriate section, and I would like to have opinions on my question.
I found, at an accredited autodesk body, a 40-hour inventor course that also allows to achieve certification.
the total cost of the course and certification is around 1000 euros.
I would like to know if, according to you, the accredited autodesk courses give more than basic knowledge about software and if the cost of the course is in line with the utility of the course itself.
Thank you very much

Michael

 

[stefanobruno]

In 40 h, on inventor, they can teach you a lot of things.
the cost is low (25euri/h), but depends on how many you will be and, consequently, what individual attention they can give you.
I hope it is for the three licenses I have, but I have not studied, so much I do not need it.

as standard, my seller proposes:
1 ) Autodesk course basic inventor : 4gg
2 ) Advanced autodesk inventor course: 3gg
3 ) self-desk course inventor : 1gg

I don't know the specific costs of these courses.
I, when I bought the licenses (2002 ), did 3 half days course, to begin with.
after 14 years there is no longer much to discover, although a comparison between users never hurts.

as a final, I tell you that there are also courses really bad, so you know well.
Over the years I have been forced to make one for certification.
It was a joke, only to be able to work with a company and, in relationship, it cost me a bang.

Bye.

 

[r-miky-b]

thanks for the answer stefanobruno
then informing me better I discovered that the course is in e-learning mode in real time, which a little discourages me.
However I found another way to get certification in my city at another autodesk center where however I will have to learn the software alone.
consider that I write from barletta (puglia) and from our areas in very few erogano courses.
Would you recommend me a way to look at the inventor's office?
I don't even have a rush

Thanks again

Michael

 

[r-miky-b]

I forgot that if I had to do the certification exam in my city, the only expense I have to deal with is that of the exam.

 

[stefanobruno]

all cite the tutorials on the web, I'm sure they don't hurt, it only takes patience to follow them, but patience one if it comes, if you need it.
to study alone and then be certified by a self-desk center I hadn't heard it yet, it's like going to school guide in the grandfather's field and then going from the school to do the exam.

 

[rf.infissi@libero.it]

thanks for the answer stefanobruno
then informing me better I discovered that the course is in e-learning mode in real time, which a little discourages me.
However I found another way to get certification in my city at another autodesk center where however I will have to learn the software alone.
consider that I write from barletta (puglia) and from our areas in very few erogano courses.
Would you recommend me a way to look at the inventor's office?
I don't even have a rush

Thanks again

Michael

I'm a pugliese province of lecce, I know quite well inventor and autocad. if it is possible you could explain to me how you can get the certification without course and the cost they have proposed.

Thank you in advance. .

 

[TECNOMODEL]

to obtain the certification you just have to take an exam, they did a session in Milan in the days after Christmas.
cost 120 euros I think.
are 30/35 questions, in English, including various topics on the software.
if you reach a 70/75% of exact answers you have certification.

 

[Zac69]

Just one thing. Regardless of doing or not a course, one thing is the certification that gives you by autodesk, one thing is the certification that gives you the dealer. there are then training centers to which self-desk from the authorization to issue the certificate on its behalf. then eyes to choice.

 

[TECNOMODEL]

do you think this certification is useful?
I don't know how interested a company is, I think they look more at design skills than knowledge of a cad system.

 

[Zac69]

in my opinion everything makes broth and a piece of extra paper does not hurt, even if it is not what opens the doors because then in the end depends whether you are able or not to design, not to model.

 

[r-miky-b]

I'm a pugliese province of lecce, I know quite well inventor and autocad. if it is possible you could explain to me how you can get the certification without course and the cost they have proposed.

Thank you in advance. .

Hello, I probably misunderstood.
in my city there is an affiliated autodesk center where I made the autocad certification.
This center does not give the course of inventor, but being affiliated autodesk, can enroll me to an official examination session autodesk of inventor at other schools nearby.
Basically it's a favor that can do me, but I should still be amazed inventor on my behalf and take the exam for a fee.

As far as the cost of the exam is concerned, I have not informed myself, since I am not in a hurry to do so.

 

[r-miky-b]

As regards certification, in my opinion it is an extra score to be included in my cv, unfortunately without significant experiences gained in the field of design and design.

 

[GiGa]

As for certification, in my opinion it is an extra score to be included in my cv, ...

Here... In my opinion it will only be one line on the resume. because then you can be the most experienced in the world, but if you find yourself working with people using the "mal" software and want you to follow their methods, then the nervous goes up. .
but well come the desire to do and learn. . .

 

[graziano-g]

Bye.
I share what giga wrote, there are people using autocad to pull rows and inventor to make snowman...
I would like to submit this to you anyway: https://www.dropbox.com/s/bsbmaozdrztb3hb/corso_autodesk_inventor.pdf?dl=0What do you think?
Hello, thank you.

 

[stefanobruno]

What do you think?

If there wasn't the 3rd block of arguments, it might be there.
would make an average of 3.33 h at a point and, taking into account that some of the points are worth 10 min., maybe you still move on.

if we add the 3rd block, done well, without just pressing the icons in correct sequence, without doing the fem analysis on the duplo bar, not to mention the blessed/ cursed plm, well, it seems really little to me.

I have always written that the rudiments of the modeling, and also of the putting into the table, they learn quickly, for the rest (third block ), better take a little more breath.
what I do not understand is the smania of learning/teaching everything and immediately.
really a designer, and I don't write it at home as in some profile that you can see here, who never used a cad, must become an inventor's expert, so much to be certified, in 40ore40?
and also with fem / plm and drafting a technical report for certification ..., de what?

 

[graziano-g]

Hi.
Is it better to avoid this?
the cost is 900/980 €....
Hello, thank you.

 

[TECNOMODEL]

in my opinion doing a course changes your way of working, often learning from self-taught you use the software to 30/40% of its potential.
and this should be something that should understand companies, unfortunately by many training is seen only as a cost.
certification instead I do not think you change your life, the decision to hire you or not is certainly not taken for this aspect.

 

[stefanobruno]

Hi.
Is it better to avoid this?
the cost is 900/980 €....
Hello, thank you.

each money spends it as you want.
If it was up to me to pay, I wouldn't do it, because I think being certified doesn't add anything to what I can do.
My clients call me for what they know is my ability, they don't care about any certification.
Let's understand, a course, when I took the first license of inventor 5.3, I did, paid by me and my two associates of the activity I have.
without that course, without books, without the web, with the 30 days of the demo I did not manage to make a piece, then I worked with autocad and this had misled me on the operating way requested by inventor.
after the course I had no problem, clear that you never stop learning.
I also did a course to be certified, but only because my client at some point only accepted certified suppliers.
I was interested in keeping it and I did it, but, I repeat, it was the only one I asked for.

(if you read me my autodesk salesman, but treat me well! )