create custom distinte for "solo-ricambi", "only-lamiere", "only-visible",...

[saracf]

Good morning to all,
having to obtain separate parts for the parts that make up our machines, I wondered if it is possible, given a machine "a" composed of "lamiere" "tornitura" "commerciali" "carpenteria" "...." derive directly from solidworks:

a separate sheet (of a machine)
a distinct turning point (of machine a)
a separate trade (of the machine a)
...
in practice I would like solidworks to "filtrate" and to insert in "distinta_lamiere" only those parts that perhaps in property I indicated as "vocedidistinta=lamiere" or "vocedidistinta=tornitura" and so on.

I also wondered if it was possible to obtain a distinction of only "visible" components that I would use as distinct spare parts (hiding the non-spare parts and launching the creation of the distinct).

 

[re_solidworks]

Good morning to all,
having to obtain separate parts for the parts that make up our machines, I wondered if it is possible, given a machine "a" composed of "lamiere" "tornitura" "commerciali" "carpenteria" "...." derive directly from solidworks:

a separate sheet (of a machine)
a distinct turning point (of machine a)
a separate trade (of the machine a)
...
in practice I would like solidworks to "filtrate" and to insert in "distinta_lamiere" only those parts that perhaps in property I indicated as "vocedidistinta=lamiere" or "vocedidistinta=tornitura" and so on.

I also wondered if it was possible to obtain a distinction of only "visible" components that I would use as distinct spare parts (hiding the non-spare parts and launching the creation of the distinct).

Hello will be,

with solidworks it is not possible to manipulate or filter the distinct at this level. you should create configurations (which have no sense of existence) from which to extract the distinct.
question: did you look at the list type of ready? make these distinct and if you create lists you create documents with image obtained from the model.

 

[saracf]

Hello re_solidworks,
the ready-type lists never explained to us (it seems to me to be back at school) and to understand the "Instructionsdal "manual manual manual" is truly arduous enterprise,
If I don't subtract you too much time and if it's not so complicated (as it seems) I would ask you to explain it to me with an example in pv, otherwise it will mean that it will make me the umpteenth note for clarifications to present at the next meeting with "ready" :d

Thanks again.

 

[re_solidworks]

Hello re_solidworks,
the ready-type lists never explained to us (it seems to me to be back at school) and to understand the "Instructionsdal "manual manual manual" is truly arduous enterprise,
If I don't subtract you too much time and if it's not so complicated (as it seems) I would ask you to explain it to me with an example in pv, otherwise it will mean that it will make me the umpteenth note for clarifications to present at the next meeting with "ready" :d

Thanks again.

Type lists are very easy to use, when you create parts and assemblies you have to assign processing and this data is used by type. the type list is a distinct monolevel as the re-epilogate, which divides the list for processing.
with the controls of the poter type create lists, I see you make an example video, but I have to find an element on which I can do it.
I don't use spare parts lists and I don't know how to use them, you should hear them.

 

[saracf]

hi, then, we created in tables, 3 new "works":
- turning
- carpentry
- assembly
then we have assigned to some parts/aid the "works" and we have seen that in "types" they are correctly divided :d

we then assigned to some parts/assiem also of the "tratt.superficie" and "tratt.termico" but these are not taken in soderation in "types": You know why and why?

I didn't have time to figure out what the "general" tabs are for "getting" "field management" that appears alongside types...

we have not understood anything about the management "spare" (also because it is mono command and the toolstip in the ready house cost too much effort and in the past they have told us that in reality "spare" would be to be customized and anyway every time, the same code would be to signal as a spare - do not remember that that code is always spare) I thought maybe to add a dedicated field in order to filter only those with the indication "spare".

Thank you very much, soon.

 

[re_solidworks]

better late than ever!:smile:

Here is the video that shows you what we did the lists, I find them very comfortable as a paper summary, even for the warehousers who with the figure immediately find the components.
http://www.youtube.com/watch?v=-azkx6bjyqm&feature=youtu.be

ciao

 

[saracf]

Here is the video that shows you what we did the lists, I find them very comfortable as a paper summary, even for the warehousers who with the figure immediately find the components.

hello and thanks, we saw the video and it seems interesting,
we tried but ready answers us with the error that I attach and freezes ... you had to configure qlc at first?

I think we have to retaliate them. . .

 

[re_solidworks]

hello and thanks, we saw the video and it seems interesting,
we tried but ready answers us with the error that I attach and freezes ... you had to configure qlc at first?

I think we have to retaliate them. . .

I did it a long time ago, but I think there's nothing to do. Are the blocks in the folder? inside the ready disk, in the cart folder, you should have files that are called:

Ria.drwdot
Ria.slddrt
ria2.drwdot
Ria2.slddrt
♪
block_ria.sldblk

If you have these should go.

Hi.