create holes on an oval face

[biro85]

Hello everyone,
I am new in this forum!

question: how do I create (holes) slits on the face of an oval object?

Thank you! :

 

[stefanobruno]

Hello everyone,
I am new in this forum!

question: how do I create (holes) slits on the face of an oval object?

Thank you! :

Hello, who are you?

It is incredible that you continue to enter the forum and ask questions without a minimum of presentation.

 

[biro85]

I am andrea, a new designer who uses inventor 2011!
I apologize for the flash presentation!! !

 

[stefanobruno]

It seems to me that your entities are surfaces, is it?
If I am, I leave to others a possible answer, I do not habit to use them to make pieces similar to that attached.

 

[SolidUser]

Hello, who are you?

It is incredible that you continue to enter the forum and ask questions without a minimum of presentation.

There are forums that make a check that if you didn't show up in the indicated area before, they don't allow you to create any topic.
You call him a moderator.

 

[stefanobruno]

richiedilo tu ...

already done in past times....

 

[biro85]

the piece is an extruded and emptied circle, the problem is that I can't make holes passing on the external face!

 

[stefanobruno]

the piece is an extruded and emptied circle, the problem is that I can't make holes passing on the external face!

Create a tangent worktop on the outer surface of the piece and on that floor do the sketch you will need to drill.

 

[biro85]

That's how you pay? but after that I do not go to pierce on the face in the right projection!
the lines(starting from the center) to 45° are the projection of the center of my hole!

 

[stefanobruno]

That's how you pay? but after that I do not go to pierce on the face in the right projection!
the lines(starting from the center) to 45° are the projection of the center of my hole!

the plan must be tangent to the sup.... and perpendicular to those that are your reference lines.
is easier to do than to explain.
If you want, attach the file.

 

[biro85]

If I put a tangent and perpendicular plan and draw my holes, then how do I put them in the circle face? Isn't there a similar way to the bouncing command?

 

[biro85]

Can ipt files be attached?

 

[Tarkus]

Can ipt files be attached?

You can attach any files, there's the appropriate flag at the top of the page where you split posts.
Just zip it.

 

[Tarkus]

already done in past times....

Even if I imagine, how did it end? :biggrin:

 

[biro85]

This is the file!

 

[stefanobruno]

modified file.
Now I'm off line, I hope you're all charo.

Bye.

 

[Preparation-H]

modified file.
Now I'm off line, I hope you're all charo.

Bye.

laundry??? :biggrin: what is a gruviera?? :. .
for a technician it was better... Uh... perforated... :smile:

Bye!
p-h

 

[biro85]

Thank you!! for patience!

next

 

[maxopus]

There are forums that make a check that if you didn't show up in the indicated area before, they don't allow you to create any topic.
You call him a moderator.

already done in past times....

I apologize for the non-relevant intervention, only to point out that I have proposed the subject in the moderator area, because the observation seems to me right and fit and the other moderators agree on what you have highlighted.

@soliduser, would you be able to report me a forum that has this functionality, so as to show it to the administrator and other moderators?
Thank you.

 

[stefanobruno]

bucato???

I like to play with words.
Also, when we were young and tech tendencies began to manifest., my brother called me "the powder technician ", so:

to do the laundry
I brought

(if you read me bonds, I applaud myself : )


@ biro85: is everything clear?