display states

[enz-OH!]

Bye to all,

I have a problem with solidworks 2014.
I made a set of sub-axis and parts. I put both sub-assistances and parts on the table using the display states.
the problem is that if I forget to add a part in the general axieme (it happened to me more than once) I don't know how to add it to a certain display status, I would like to know if there is a way to do it.
I hope I explained.
if I add it as I have always done, when I open the tables (made with the visualization states) this part appears in all the tables forcing me to redesign the "incasinate" views.
Thank you in advance.

win

 

[MassiVonWeizen]

why make subset tables and parts using the display states of the axieme (if I correctly understood your procedure)? is it not 2 better to make the table using the individual files together and aside?

if I add them as I always have

if you tell us how we can exclude a metdo
you could right-click the display status >properties>hides new components if inactive

 

[Biggmetals]

the problem is that if I forget to add a part in the general axieme (it happened to me more than once) I don't know how to add it to a certain display status, I would like to know if there is a way to do it.
I hope I explained.
if I add it as I have always done, when I open the tables (made with the visualization states) this part appears in all the tables forcing me to redesign the "incasinate" views.

nb: I have version 2016, I don't know if it works equal to 2014 but in case it can be useful for someone else maybe.

to insert it into a certain display state just have it active at the time of "trascining" and to prevent it appearing in all display states just scourge this in the properties of the display states:
but you can also hide the single component by pressing tab while the cursor and on it and in the display state where you don't need to see it. (to make faster is meant, always in case certain components have to appear only in some and not in all)

 

[enz-OH!]

Hello Massivonwiezen,

first of all thanks for the attention.
I explain: the axieme is a shed formed by beams, tubular, plate, etc.
the workshop must be delivered the tables both of the parts (trave) for cuts, etc. both of the subaxis (columns formed by beams, anchor plates, reinforcement handkerchiefs, etc.) for welding.
I have inserted in the general axieme the subaxis of these columns, I have used commands such as linear repetition, mirror, etc. to not go to place a column at a time.
Sometimes I do not insert in the column (subassieme) some plates (parts) because using repetition, etc. I place them not as I want, then place the column (subassieme) without these plates (parts) and then the plates (parts), all in the general axieme.
However in the column boards I need those plates there are, so I use the display status in the general axieme by inserting the column (subassieme) with the plates (parts) and put at the table the display status just created.
the problem is that if I forget to insert a piece into the general axieme and insert it after creating for example 2 states of display of 2 columns with their plates, but I want it to appear in a display state and not in the other, the solidworks inserts it in all the existing visualization states, "casing" the tables.
Thank you again.

win

 

[enz-OH!]

Hello biggmetals,

I tried to follow your suggestion and Massivonwiezen, but in 2014 in property it makes me change only the name of the state, do not come out advanced properties unfortunately.
I think that was the solution to my problem.
if you have other suggestions write as well.
Thank you in advance.

win

 

[MassiVonWeizen]

the workshop must be delivered the tables both of the parts (trave) for cuts, etc. both of the subaxis (columns formed by beams, anchoring plates, reinforcement handkerchiefs, etc.) for welding.

I doubt you're not working in a multibody environment.
I have made time behind structures made practically only of columns and crosses and, although unmadonnando, I managed everything with the configurations of the parts.
for example I had 10 columns with the same profile and plate and puncture arranged in various ways and I made only one file with 10 configurations; made a table is saved by name and you change the column configuration by setting the design equally, but recovering a 50% or more.
it manage component states with the 20q14 make properties on the affected part and set the areas indicated in red of the imagelink of the treadh from which I obtained the, probable, solution. https://forum.solidworks.com/thread/89975

 

[enz-OH!]

Bye to all,

no massivonwiezen I am not working in environment part multibody, since I do not master well use it only with simple structures (doors, ramps, stairs, etc.). You're not the first one who recommends it to me, I'm practicing it to use it with sheds.
thanks I solved with the procedure in the properties of the part you posted, I hid the part state by state.
I’ve seen that in the curtain “change display properties” you can specify the display states in which to hide it, but it doesn’t work (as it says perhaps is a program bug) then I proceeded state by state as I wrote before.
Thank you again.

win

 

[MassiVonWeizen]

if you make carpentry use multibody is practically mandatory. The benefits are many

 

[MassiVonWeizen]

tonight if I find them I attach a pair of multibody columns configured in 2014

 

[enz-OH!]

thanks to the massivonwiezen thought, if you find them you have 2 coffees paid, if you do not find only 1 if you are from the salter parts.
I also practice time cuts, but I still don't master the multibody well, coming from precision mechanics I used it a few times.
Greetings.

 

[MassiVonWeizen]

multibody is also used in precision mechanics. And I would say a lot.
the multibody is corresponding to the monolithic welded piece. in the tutorials the topic is definitely treated since years back was a differentiation from other cad and a strength point of solidworks

 

[enz-OH!]

I didn't know.
Then I correct myself, coming from the precision mechanics of the company where I worked, I used it a few times. I first realized parts formed by a body and more functions to be exported to realize tool paths with another program.
Greetings.

 

[MassiVonWeizen]

I'll train you two files. I made them new because I can't find them anymore, so they're very rough but should explain the concept.
the column file is a classic multibody in which the side plates are managed by means of configurations, changing both the presence and the position. it can be pushed beyond managing the quantities, but more variables are created more weighted must be the planning upstream of the modeling.
the beam file is always a multibody but contains a part in both configured part. This can be useful when you have standard designs that are used systematically or you have many equal plates (they could still be other objects) that are used on multiple beams and columns and which are already required drilled before welding and therefore have their own design. so doing I insert a part in the part, I manage the configuration if I have more than one and in the table I will not have to quota it every time and just give the reference code and the positioning regarding the surrounding geometry

 

[enz-OH!]

Hello Massivonwiezen,

thanks not only for thought but also for availability since you have redesigned.
I'm studying the column file.
I am practicing with an extension of a shed already made using multibody and configurations for presences and bracket positions, etc.
I'm learning a lot of steps that I would take longer to understand.
coffee goes up to 3, a greeting.

win