finished dimensions

[Beth]

Hello, everyone.

it is possible with create obtain the finite size of a part automatically, create a parameter and resume it then
in the table?

 

[DANI-3D]

Hi.

with relationships you should have no problem creating parameters to be recalled in the quotas or notes of the table.

 

[Beth]

Thank you, dani 3d, I think I understand what you say, but in relationships you still have to enter
manually the quota, I asked if there was an automatic detection of the size and the possible recovery in the parameter.
using model check for example automatically the finished size is given but can it be transformed into a parameter?

 

[DANI-3D]

... but in relationships you have to enter
manually the quota ...

not necessarily, you can automatically recall any quota used in the various building features, or dimensional analysis saved in the model tree.
I would leave overall_size, because of difficult management and especially for pieces a minimum complicated are very indicative measures.

 

[Beth]

but so much to do tests, you know how to write it in the overall_size relationships

thanks in advance

 

[DANI-3D]

You have to configure the modelcheck in the right way, but if you don't know it, it's not trivial at all. I hit my head several years ago to upgrade an old project where many parameters were missing, I managed but it was hard.
to start with an eye here:http://www.cad3d.it/forum1/threads/guida-alluso-di-modelcheck-per-parti-standard-pdf.41795/also do a search in the forum, there are other discussions that treat the topic.

 

[freexf]

When you launch modelcheck, the parameter associated with the overall_size is created.
example if you write in the start file Prat_add_chk_param xyz overall_ a xyz parameter is created that you can then use in relationships.. what's wrong with this?

 

[Beth]

I'll give you some evidence and tell you the result
thank you very much for the advice

 

[Beth]

When you launch modelcheck, the parameter associated with the overall_size is created.
example if you write in the start file Prat_add_chk_param xyz overall_a xyz parameter is created that you can then use in relationships.. what's wrong with this?

Sorry, but I can't get anything good.
I can't understand where you have to write Prat_add_chk_param xyz overall_size.
please give me more lights. Is it about start part or model check configuration file?
Thank you.

 

[freexf]

of modelchek (.mcs) starters

 

[Beth]

Hello everyone

I have a question.

if I have a part with a size parameter that recalls the xyz size values (quotes or annotations of the model) and the mirror creating a part b ,
How can I relate the size to with b so that when I change the size to the size of b are properly updated?

 

[freexf]

Something's wrong with what you say.
1.spec with 'geometria' option both with dependency option and without dependence => parameters go but the annotations of the model do not go)
2.spec with 'geometria and feature' option => parameters go and annotations go but no dependence on the mother model.

 

[Beth]

Thank you for answering,

we forget for a moment the annotations

if mirror with dependency geometry option you the parameters pass but to me it turns out that if I change the mother part the updates to the size are not updated

 

[freexf]

It would be a yellow.
proof made by me attached

 

[Beth]

Thanks for the video,

I make the mirror together, but

I try to make a movie

 

[Beth]

If you have any advice?

 

[320i S]

Thanks for the video,

I make the mirror together, but

I try to make a movie

and opening the mirrored part on his own, regenerating does not update?

 

[freexf]

Strange.
In theory, the update will be seen while together. There is no need to open the mirrored part.
Can you attach the original part?

 

[320i S]

Strange.
In theory, the update will be seen while together. There is no need to open the mirrored part.
Can you attach the original part?

In fact, I suspect there is a setting, which does not allow automatic updating

 

[Beth]

Thank you for answering,

I have no problem with the updates of the mirrored geometry that works perfectly. I have problems with the size parameter of the mirrored part that unlike the original part does not update the new size.

Can I attach the aid if you want, I use I create 5 there are problems?