flat repetition

[deep70]

Hello everyone,
I have a problem with flat repetition, in model 3d does it quietly, but then at the table at the call of the weave I find myself with a lot of view not defined as from images, I remember long ago to have had something similar but I am not sure, in fact that time was suspended, I checked there is the check on "suspended" but also removing the result does not change.
Thank you all very much as always for any given answers.
ps: the model consists of 5 parts of which only two with folds (in extremes)

 

[MassiVonWeizen]

if you make the sight flattened the flat repetition must be active.
If you have multiple sheets in a multibody, as you can see from the second image, to have the flattened view of a sheet you have to recall the specific body otherwise you are viewing the whole model.
that mask of the second magician does not serve and does not say anything useful; what is this configuration?
I would like to ask the Commission to take the necessary steps to ensure that we are able to do so. derived configuration development is created automatically when, in the design environment, you create a view of a body by selecting flat repetition from the property manager; This makes the environment part of configuration default have the flat repetition suspended and the derived configuration development have the active flat repetition. if there are more bodies made of sheet metal there will be for each one derived configuration development. quando una di queste derived configuration is active all remaining crpi are automatically hiddenin case that during modeling you switch from one configuration to another by activating and deactivating, for various verifications, the flat repetitions before making the drawing you have to:
.check that the active configuration is default and check that all flat reps are suspended
.verify that every single derived repetition lowers only one active flat repetition and that the development of a single body is visible; if it is in confusion to eliminate all derived configurations and recreate them through the insertion of views flat repetition

 

[deep70]

if you make the sight flattened the flat repetition must be active.
If you have multiple sheets in a multibody, as you can see from the second image, to have the flattened view of a sheet you have to recall the specific body otherwise you are viewing the whole model.
that mask of the second magician does not serve and does not say anything useful; what is this configuration?
I would like to ask the Commission to take the necessary steps to ensure that we are able to do so. derived configuration development is created automatically when, in the design environment, you create a view of a body by selecting flat repetition from the property manager; This makes the environment part of configuration default have the flat repetition suspended and the derived configuration development have the active flat repetition. if there are more bodies made of sheet metal there will be for each one derived configuration development. quando una di queste derived configuration is active all remaining crpi are automatically hidden
in case that during modeling you switch from one configuration to another by activating and deactivating, for various verifications, the flat repetitions before making the drawing you have to:
.check that the active configuration is default and check that all flat reps are suspended
.verify that every single derived repetition lowers only one active flat repetition and that the development of a single body is visible; if it is in confusion to eliminate all derived configurations and recreate them through the insertion of views flat repetition

thanks many for the massive response, as always resolutive, the problem is now another, that is one of the flat repetitions does not come out, while in model 3d yes.

 

[MassiVonWeizen]

But the problem is now another one, that is one of the flat repetitions does not come out, while in model 3d yes.

to me it seems the same problem that I can only give the same answer since from the image you can not deduct anything else, that is: check that in the configuration development of that body is active the respective flat repetition

 

[deep70]

It seems active, I don't come out. I'll send you the model if you can take a look, you'll do me a great favor.

 

[deep70]

 

[deep70]

Unfortunately the file is too heavy and does not charge me. .

 

[MassiVonWeizen]

Does the design view recall that configuration?

use a website like dorpbox. What's wrong with you? would be the case to write it on the profile.. .

 

[deep70]

I have 2018, the view recalls that configuration, could go even a stp file?

 

[MassiVonWeizen]

Could go even a stp file?

No. the step file does not have the function shaft. I should convert the corpses into sheet metal or do it again and it wouldn't help to understand the problem

ho la 2018

I hope to see it written on the profile

 

[MassiVonWeizen]

is the view set on flat repetition?
if you, delete the development configuration of that body and recreate it through the insertion of the view

 

[deep70]

No. the step file does not have the function shaft. I should convert the corpses into sheet metal or do it again and it wouldn't help to understand the problem

I hope to see it written on the profile

you are right I have to update the profile, sincerely the piece as always is done in the most complicated way possible, in the end it is a sheet quite simple, I will ask tomorrow if they make me refer it to me or if they have a solution to the problem.

 

[deep70]

is the view set on flat repetition?
if you, delete the development configuration of that body and recreate it through the insertion of the view

I tried but it does not let me do it, it gives me - impossible to eliminate the selected entities-

 

[MassiVonWeizen]

is the view set on flat repetition?

???

impossible to eliminate selected entities

You took out the view from the drawing and then saved it?

 

[deep70]

I noticed now that two of the configurations give me the same development. .

I tried but it does not let me do it, it gives me - impossible to eliminate the selected entities-

Now this message comes to me:

 

[MassiVonWeizen]

if you haven't already listed it deletes the design and refract after eliminating development configurations.
if you have already quoted, do a print for vision and delete the design and do it again

 

[deep70]

recapitulating, I deleted the configuration and remade, but the result is that as before on the table you do not see a definite view. .
I also tried to remake the table without result, or better with the result in the image posted here. .

 

[MassiVonWeizen]

cos I know.? will you have renamed the configuration?
then I see in part 7 flat repetition, but only 5 derived configurations. ...
I understand that the nervous loses calm and sends in confusion, but if it happens you have to clean up the situation.
parts from the clean side file disc development configurations
take a sheet and mark each flat repetition (clicking on and activating it and then suspending it) to which body corresponds.
in drawing parts from the insertion of the views following the order of the flat repetition (if you want you can rename them with sequential numbers) so that in the part file each development configuration (do not rename them) has the same sequence of the flat repetition; therefore development will correspond to flat repetition1, development1 to flat repetition3 and so on


to know if the flattened view of that body works do this test:
with function cancella corpHe eliminates all except the offender.
now in the part you should have only one body and only one flat repetition function
do the drawing, in this case without having to select any body obviously, and set the view in flat repetition mode. if it works you can continue to reason otherwise there are other problems

 

[MassiVonWeizen]

attach equally the file and design that even if I do not have 2018 gives the possibility to others to help

 

[deep70]

Here I am, in essence I have eliminated all the bodies and left the incriminated one, strangely I still have two flat repetitions instead of one, I press that the model on it I did, sincerely I do not understand the reason to model a simple sheet complicating so life, unfortunately the file weighs 15 mb and I can not post it even compressed. .