inventor 2010 very slow in positioning constraints

[dicifa]

hi to everyone, I have a huge problem....I designed a very big structure with the chassis generator and in the processing phases I have no problem, the problem comes when I go to place every particular sigolo, also a single bolt....esosiziono a bolt with the pin/hole bond on a hole and from there it takes about 1 minute to update.this causes me a loss of time and above all a great loss of "pazi" ! ! !
I use a processor amd athlon(tm)64x2 dual core processor 5000+2,60 ghz, ram 3 gb, system 32 bit, video card nvidia ge force g100......this was purchased in June 2009....I also tried to change the user interface and I am using the classic one without any improvement. ....
Can any of you help me? :36_6_1:

 

[davide75]

Did you put up the sp1? ?

 

[dicifa]

No, I prove subito. ...

 

[Tarkus]

hi to everyone, I have a huge problem....I designed a very big structure with the chassis generator and in the phases of .........ghz, ram 3 gb, system 32 bit, video card nvidia ge force g100.........I also tried to change the user interface and I am using the classic one without any improvement. ....
Can any of you help me? :36_6_1:

How big?
However unfortunately it happened to me with 2009... I knew that with 2010 they had solved.

 

[dicifa]

I installed the sp 1, I restarted the pc but the problem persists.....possible that the problem is why the work was done with the chassis generator?

tarkus:the size of the structure is about 20 meters x 10 high 4, all built with 220 ipe and all 180 beams (a traverse every about one meter), 80x80x8 angles and various sp10 plates for fixing each other, sp80 greek panels for the roof....and of cosiguency I need to insert all the bolting......... I don't understand exactly where the problem is.... .

 

[Peppe]

I installed the sp 1, I restarted the pc but the problem persists.....possible that the problem is why the work was done with the chassis generator?

tarkus:the size of the structure is about 20 meters x 10 high 4, all built with 220 ipe and all 180 beams (a traverse every about one meter), 80x80x8 angles and various sp10 plates for fixing each other, sp80 greek panels for the roof....and of cosiguency I need to insert all the bolting......... I don't understand exactly where the problem is.... .

Do you have various activities around?

 

[Tarkus]

It does not refer to the physical size of the axieme, but to how many parts and celebrations make it (the two numbers below the right of the graphic window, next to the icon of the parabolic antenna).
proof, as it already mentioned, he knew how to remove the activity from the skeleton's sketch and other adaptiveities that you're around...

 

[pagnotz]

In fact, these problems usually arise when there are many activities that are to be recalculated or not completely bound parts that can move during the placement of other parts.

 

[dicifa]

the figures are:
-documents opened in session=109 (corresponds to the number immediately next to the antenna)
- total competitions in the document=847 (subit to the left of the previous digit).
Can you tell me what they match?

in the structure there are many adactivity and I have eliminated all but some do not give me the possibility to eliminate them, i.e., there is the adactivity symbol but inside the "history" I cannot evigorate "adactivity"... how do I eleminate them all? Do I have to pass one by one?

 

[Gioacchino]

try to remove the flags from 'application options':
- enables redundancy bond analysis
- ablitita analysis related errors

Let us know

 

[dicifa]

are not plagued, the only things that are plagued are:
- audio constraint notification
-habilita projection geometry edge/line closed associativa during local modeling....

 

[Tarkus]

the figures are:
-documents opened in session=109 (corresponds to the number immediately next to the antenna)
- total competitions in the document=847 (subit to the left of the previous digit).
You can tell me the cosa corrisposingno?
...... .
All of them? Do I have to pass one by one?

open files are practically the parts and subassiems you are using for
compose the axieme that you opened;
recurrences are the times that these parts or subaxes are repeated with series or other "doubles"
Anyway:
847+109=956 parts, it's not small, but it's not even a big set, it's not the size that slows down.
by my experience, I tell you that it does especially with the chassis generator or when you use a set with many parts created by a single derived sketch. ...
I add that I don't need anything to deflag the two constraints analysis that suggests jubilee. When he decides to make a snail, there's nothing to do. .at least until someone suggests the remedy :biggrin::biggrin:

 

[dicifa]

...maybe I understand what the problem is; I know that it is due to the poor performance of the pc. the installation manual of inventor 2010 asks that if you work with assemblies with over 1000 parts it is obvious a 64-bit operating system, processor amd 64 and at least 6 gb ram.... the requirements there are all, except the operating system because I saw 32 bits.... I added 2 g ram(even if not use them)and changed the video card....
I think the only solution is to return to our dear old xp, which will certainly be faster than view.
What do you think?

 

[Stiky]

...maybe I understand what the problem is; I know that it is due to the poor performance of the pc. the installation manual of inventor 2010 asks that if you work with assemblies with over 1000 parts it is obvious a 64-bit operating system, processor amd 64 and at least 6 gb ram.... the requirements there are all, except the operating system because I saw 32 bits.... I added 2 g ram(even if not use them)and changed the video card....
I think the only solution is to return to our dear old xp, which will certainly be faster than view.
What do you think?

I wouldn't be so sure! I have seen 64 for at least a year and I have never had any problems or crashes.
the problem is that with a 32-bit so each application can use at most 2gb of ram (regardless of how much you install on pc). with so to 64bit superi and much this threshold. So second you have to switch to a 64bit so. View64 works well, if you turn off all the gadget you have, xp64 is dead!

to give you an example yesterday I was working on a set of 800 parts and checking in inventory resources management used 3.5gb ram. the number of parts in a set is indicative it is also necessary to consider that size have the files of the parts, which changes you are doing, or if you intend to make a table, in this case you must insert in the speech also the video card.

 

[dicifa]

..then the advice you give me is to install view 64?
What do you mean by:"vista64 works well, if you turn off all the gadgets it has, xp64 is dead!"....any gadget?

 

[Stiky]

find more info on the network: However the aero interface definitely, the slideshow, impose the performance of the ws on "rule x have the best performance".