mating "thelescopic": how to do?

[reggio]

hi, I would like to get to create a promotional video of a telescoping tape, for now I can't even parade as it would happen in reality...
I found the video below and with that stand trying to experiment on this set that I attach...

I can't do so that, dragging out the red, they also escape the blue and yellow ... at the same speed so that, after the race of red they also end the races of blue and yellow...

How would you do that?

 

[meccanicamg]

you can't do it if you use the cinema module with contact bodies. pull the red that comes out and drags others when they go to the hooks funds.
alternative n linear motors.

 

[MassiVonWeizen]

from the evidence I'm doing you need to set the report correctly.
with 1:1 moves only one component
with 1:2 move both and the spacing remains constant between component 1-2 and component 2-3
this because, I suppose, use a same starting reference then looking at the video if the blue moves 1 from the green face the purple must move 2. I'm not sure, it's the first time I've been using this mating and I'm going to keep it.
otherwise you must give it the reference in the cells below those of direction so that the blue moves with reference to purple and green with reference to blue.
to stop them not use simple drag but the function moves and impose the stop in collision

 

[MassiVonWeizen]

Here's an example.
the stop is managed with a limit distance

 

[MassiVonWeizen]

@reggio, it would be nice that at least older users responded to discussions

 

[reggio]

@reggio, it would be nice that at least older users responded to discussions

Good Mass Sunday, you are fully right, I apologize,
I had the urgency to capture a video presentation "telescopic immediately" and took advantage of the forum, then sent the acrocchio, covered me with other urgencies without leaving me time to complete, as it must and in a definitive way the argument, which I escaped and exited from the "chamber of primary blood urgencies"

I really forgive myself, for the moment I renew my thanks for the time, competence and help you can always dedicate.

... but "old-time users" no daii ... I prefer " mature users"

 

[TorMec]

hi, I would like to get to create a promotional video of a telescoping tape, for now I can't even parade as it would happen in reality...
I found the video below and with that stand trying to experiment on this set that I attach...

I can't do so that, dragging out the red, they also escape the blue and yellow ... at the same speed so that, after the race of red they also end the races of blue and yellow...

How would you do that?

you have to couple each component to its neighbor who drags it or pushes it, the same thing repeats between the second and third component is so on.use advanced couplings away.

 

[MassiVonWeizen]

you have to couple each component to its neighbor who drags it or pushes it, the same thing repeats between the second and third component is so on.use advanced couplings away.

It's a pretty vague help.
advanced coupling of distance does not exist with this term and it is not clear that you should use thelinear/linear coupling.do not explain how the mating parameters should be set.

the solution is located at post #3 and #4 with detailed explanation and example set where you can check the settings

you forgot to answer this discussion

Aspetto personalizzato per forature

Buongiorno a tutti, volevo chiedere se su solidworks c'è la possibilità di configurare il colore dei fori a seconda della tipologia.Intendo ad esempio foro filettato di qualunque tipo ad esepio giallo, foro in tolleranza H7 verde, foro in tolleranza E8 blu e cosi via.L'obiettivo è quello di...

www.cad3d.it

 

[TorMec]

It's a pretty vague help.
advanced coupling of distance does not exist with this term and it is not clear that you should use thelinear/linear coupling.do not explain how the mating parameters should be set.

the solution is located at post #3 and #4 with detailed explanation and example set where you can check the settings

you forgot to answer this discussion

Aspetto personalizzato per forature

Buongiorno a tutti, volevo chiedere se su solidworks c'è la possibilità di configurare il colore dei fori a seconda della tipologia.Intendo ad esempio foro filettato di qualunque tipo ad esepio giallo, foro in tolleranza H7 verde, foro in tolleranza E8 blu e cosi via.L'obiettivo è quello di...

www.cad3d.it

Sorry I meant limit distance, I thought you understood.

 

[MassiVonWeizen]

limit distance does not allow to perform the movement of the initial video and does not have advanced settings to do so

 

[TorMec]

limit distance does not allow to perform the movement of the initial video and does not have advanced settings to do so

I saw the video now, I was running.The limit distance moves one at a time, I didn't realize that they had to be synchronized by the first post.thanks

 

[Freddygol]

Good morning to all, even if it seems to me a closed speech, I say my experience. I do not use the linear-linear command but use a distance at altitude for the first piece, then symmetrical for the intermediate pieces, the symmetry the "chain" for how many telescopic pieces there are.a fundamental difference that I could notice is that with linear-linear you can vary the percentage of edge, as I do not. Besides I never tried, but it seems to me that with linear-linear you can mate only two pieces, that at the limit one repeats the command n times..... .