post processor mastercam x fagor 8055i

[giobos]

Good morning to all,
I would kindly need to know if any of you can give me directions on where to go to visit or if you can send me the post processor for mastercam for a fagor 8055 control. the machine is a vertical cutter with 5 interpolated axles (switching table).

Thank you very much

thanks to all

 

[kuman]

Hi, if I have some time I can arrange a mastercam post... send me a file where you show me how you want the program to come... I don't know, a two-dimensional profile program, so that I have an example

 

[giobos]

Hi, if I have some time I can arrange a mastercam post... send me a file where you show me how you want the program to come... I don't know, a two-dimensional profile program, so that I have an example

Hello kuman,
thanks to the interest...in reality the control has to manage 5 axes and not only 3. Don't you know where I can find him?? because I heard that for the 5 axes it is not so easy to write..confermi? ?

off topic: how do you write a post-processor?? in what language do you write? ?

Thank you. .

 

[Mike1967]

Hi, if I have some time I can arrange a mastercam post... send me a file where you show me how you want the program to come... I don't know, a two-dimensional profile program, so that I have an example

Please don't use the case.
Thank you. :smile:

 

[carpentiere]

help me, too. I would need a fanuc 18i tb mounted on lathe biglia 550 5 axes

 

[kuman]

Okay carpenter, what do you need? ? ?
- - - updated - - - -Didn't Mike get my answer? ? ?

 

[Mike1967]

Okay carpenter, what do you need? ? ?
- - - updated - - - -Didn't Mike get my answer? ? ?

What answer?

 

[kuman]

I mean yobos, I'm sorry! !

 

[Mike1967]

I mean yobos, I'm sorry! !

nessun problemma... :smile:

 

[giobos]

I mean yobos, I'm sorry! !

hi to all..discussed if I find a post a little old..kuman the file that I want it to come out is a classic gcode with .pim extension (see attachment)...g0 g1 etc. to understand us. .

The post has already done it to me, but I would like to deepen the question more. . .

Thank you very much and I apologize to the moderators if I reopened an old post..

Thanks again, sorry

Thursday

 

[Mike1967]

hi to all..discussed if i find a post a little old..kuman the file that i want it to come out is a classic gcode with .pim extension (see attachment)...g0 g1 etc. to understand us. .

the post has already done it to me, but i would like to deepen the question more. . .

thank you very much and i apologize to the moderators if i reopened an old post..

thanks again, sorry

thursday

no problem!
i hope you find help. :smile:

 

[kuman]

Excuse me, deepen in what sense?? ? ...the mp language (mastercam post) is a set of codes that is not that I can explain it so in two words....if you're interested I'm slowly putting on the network of tutorials.. . . http://encodematic.altervista.org/services.html If you need some specific clarification, don't worry.
Bye.

 

[giobos]

Excuse me, deepen in what sense?? ? ...the mp language (mastercam post) is a set of codes that is not that I can explain it so in two words....if you're interested I'm slowly putting on the network of tutorials.. . . http://encodematic.altervista.org/services.html If you need some specific clarification, don't worry.
Bye.

Thank you kuman,

My goal now is to be able to change a post already made by others, like to remove point and comma, to put in order the rows (type g55 before t1 etc.)..how can I do?

Thank you.

 

[kuman]

Look, at distance so it's not easy. ..however you ask me about the relatively simple changes....if you say, as you know, you could send me your post, then you tell me about the changes you want to do, I will do it and compare the two posts and see how I acted....poi se want me doamnde....so via forum I don't know how else to do. . .

 

[giobos]

Look, at distance so it's not easy. ..however you ask me about the relatively simple changes....if you say, as you know, you could send me your post, then you tell me about the changes you want to do, I will do it and compare the two posts and see how I acted....poi se want me doamnde....so via forum I don't know how else to do. . .

thank you kuman, I did somehow by:biggrin: I realized that it was a modified and adapted post (for a few things to tell the truth) of a fanuc 5 axes. now I would always like to change a post of a 3 axle machine, regarding the management change tool, filter tolerance bows on interpolated movements, but the language is a little particular. Can I put an example? or better private message?

Thank you. .

 

[kuman]

go quiet, without any problem... tell me exactly what you need that if you have a minimum of hands in dough we solve everything

 

[giobos]

go quiet, without any problem... tell me exactly what you need that if you have a minimum of hands in dough we solve everything

perfect kuman...I have a 3 axis pantograph and I would like the post (made by I don't know who for this machine) to break the bows, as if I plan to tell the machine to make an arc greater than 90 degrees in a way, the machine does it to me in the opposite direction..I have to send you the post? Do I need to contact you in private?

Thank you.

 

[kuman]

hi, for this change it would be better to send me a zip2go file if you can do it...otherwise send me the post and the .control file associated and I make you the changes. . Send it here or private is the same