quota filetto

[Cla]

Good morning to all, I was trying to quote threads both on holes and "full" elements. I have made some cosmetics features and already manages strange (where to measure the handpiece) understand which threads I have in front. I would therefore like to understand how to customize my share maybe better understand how to handle the cosmetic fillets.

Hello everyone

:biggrin::biggrin::

 

[maxopus]

I usually prefer to use standard thread holes that already have the note with all indications according to the iso standard.

If you make the holes with cosmetic the note, you do it in hand.
usually the correct preforum and the cosmetic surface with a diameter equal to the nominal value (diameter 10 per hole m10).

or build a note with the preset parameters that go to read the quotas of the foreskin and cosmetic.

 

[Cla]

regarding full elements? ?type pins or similar things? ?if I have to make a screw for example with m20 which diameter should I draw? ? I have seen that between the various parameters there are several things but I do not honestly understand how I do without literature to make a m20...? ?

If I make a 20-cylinder, when the cosmetic command asks me the diameter and imposed 20 thread is made out of geometry...the diameter I have to draw to make a m20 would be the outer one? ?

 

[lollone]

I'm sorry. I don't know if I understand your problem.
if you draw a screw (external fingering) you will make a feature and the cosmetic will go to represent the core of the thread...so on a m10 (d.10mm pin) the cosmetic will have diameter d.8.344.
at the end you will put as suffix at the height of diameter 10 the letter m.

 

[ss900]

I usually also do not use standard threaded holes, but I prefer cosmetic thread.

if you need to make a threaded hole m3:
make a hole (extrusion or revolution) having diameter = to the diameter of hazelnut (2.5mm) and then make the cosmetic thread with diamtro 3 having the desired depth.

if you have to make a screw m3:
make a cylinder diameter 3, then make the cosmetic thread diamtro 2.5 (diam. of hazel), of the length you need.

If you make a table you can verify that they are properly represented.
to quote them I made a macro, which by clicking on the quota automously inserts the m in front of the value of the diameter.

I hope I've been clear and helpful.
Bye.

 

[lollone]

Can you pass the macro? excellent!... just not to do it!
I use tables to make threaded holes and gases, even those flushed and laminated! is faster!

 

[Cla]

Thank you.

understood... it seemed to me to be able to solve in a less laborious way... I must always know the diameter of the thread profile to do it with cosmetic so... mmm

If I would like to make a fictitious quota... ignore the value from geometry as I do? ? ?

 

[lollone]

I mean? do a bit of a hand?
I don't know if you want to do things like that? The mistake lives on these things!
cmq for threaded holes you should use thread tables!to the most you create them according to your needs!
the year put right to speed the process for the creation of threaded holes.

 

[maxopus]

Thank you.

understood... it seemed to me to be able to solve in a less laborious way... I must always know the diameter of the thread profile to do it with cosmetic so... mmm

If I would like to make a fictitious quota... ignore the value from geometry as I do? ? ?

just enter the @o string and text and you can write what you want ... highly recommended procedure. as regards the measures to be remembered on hazelnuts and fillets it is enough to create fdu. so you don't have to remember the individual values.

 

[lollone]

maxopus...but in theory @o can't just put it on odds created in manina?

 

[maxopus]

maxopus...but in theory @o can't just put it on odds created in manina?

You can only do it on manual quotas.

 

[dema]

...
if you need to make a threaded hole m3:
make a hole (extrusion or revolution) having diameter = to the diameter of hazelnut (2.5mm) and then make the cosmetic thread with diamtro 3 having the desired depth.

if you have to make a screw m3:
make a cylinder diameter 3, then make the cosmetic thread diamtro 2.5 (diam. of hazel), of the length you need.

If you make a table you can verify that they are properly represented.
...

they are not represented properly but with interference because you want to put a male of three in a female of 2.5.

the screw should be drawn with the diameter of the part equal to the hazelnut in this case 2.5 and then the cosmetic of 3.

I take advantage of it to introduce myself as it is a bit that I am enrolled but this is my first message, but since the information for how I happen it seemed wrong and the user who made the request seems to me at first better now than after creating the entire library.

 

[dema]

I add a couple of attachments the first jpg is an example of table setting, while in the second contains the screw and compass seen in the image

 

[lollone]

look that cosmetic always represents the core of the fillet (victims or mumps it is)!! !
Look at technical drawing regulations if you don't believe me...

 

[dema]

look that cosmetic always represents the core of the fillet (victims or mumps it is)!! !
Look at technical drawing regulations if you don't believe me...

It is not that I do not believe you but from outside I have worked for two multinationals (small works of commissioning) of the mechanical sector and they work so in fact the parts I have put are their commercials.

 

[lollone]

Look, I've never worked for multinationals, but I don't think that means much.
cosmetic go to represent the fine line of representation of the thread hazel in technical design.
I can't post external links from the forum otherwise I would show you...but I recommend doing a search.
It seems very strange to me your representation.

 

[dema]

Look, I've never worked for multinationals. . .

I didn't write it to make me beautiful, it was just to say that I didn't make it up, I just took a piece of a studio and put it on the table.

 

[lollone]

I just wanted to advise you to check! not accept what is put in your hand if you are not sure it is right.
unless in the press the display is as in the pdf above.
then if there is any other legislation that represents it so I don't know!

 

[dema]

I just wanted to advise you to check! not accept what is put in your hand if you are not sure it is right.
unless in the press the display is as in the pdf above.
then if there is any other legislation that represents it so I don't know!

you know the law is that company them, they are so big and we as external study so small that if they say jump we do not answer as high.

they probably want so to avoid seeing interference that especially on computer in case he has to look for trouble.

 

[lollone]

This could be another explanation. . .
But I personally disagree to do so!... I say it for ss900.
you would find yourself having a library that does not follow the regulations of representation of threads (uni3978)