replace a set with a part in the drawing

[esatb]

Bye to all,
I always need to replace a set with a part in the drawing.
I'll spend better.
I have a 2d design connected with 3d of a set. for reasons of simplicity except this together as part and gate or renounce the axieme.when I go to open the drawing I see only empty rectangles. I tried to change the suffix (type) of the part file from .sldprt to sldasm.... I put the same name as the previous witness, but... Nothing to do.
Does anyone have any ideas or do you know any tricks? ?
thank you so much and good work to all

esatb

 

[volaff]

show up early, no? :

 

[esatb]

ah, yes.? ?
even after three years do you have to show up?? :
but before losing energy on these things would not it be better to answer the question made? ?
Thank you.

 

[volaff]

I would say that before spending energy to answer the question made it should be at least educated and respect the regulation.
Good evening.
Surely someone will know how to answer the best!

 

[esatb]

I would say that before spending energy to answer the question made it should be at least educated and respect the regulation.
Good evening.
Surely someone will know how to answer the best!

Which one can answer please? ?

 

[meccanicamg]

You can't expect to do whatever you want or here or with the software. Do replacements properly and then there will always be problems if you replace a part to a set. use methods to freeze geometry, ghost, light weight, configuration.... but do not do so...

 

[esatb]

I asked the question thinking of participating in a forum of specialists, I never thought of dealing with arrogant and bullying.
I don't have time to stay behind the people who fly with their finger in the c...

 

[volaff]

I asked the question thinking of participating in a forum of specialists, I never thought of dealing with arrogant and bullying.
I don't have time to stay behind the people who fly with their finger in the c...

Well if we (speaking of users because I am not a specialist) we are "arrogants and bullying" I think you are ignorant (....."with arrogant and bullying") since they say non gods!

Look at this! !

 

[marcof]

I asked the question thinking about participating in a specialist forum

and you thought well... here on cad3d there are people with counterfeit.

I never thought I was dealing with arrogant and bullying.

the main problem is that you have not been able to formulate a question with the slightest syndicale of clarity, without attaching a rag of sample files etc., so who reads you understand that you are combining invenous cases by erasing assemblies and renameing parts, but not having the crystal bowl fails to accurately frame the problem, which is not of swx but your that you do not know how to use it.
It is not a question of arrogance on our part, believe me, it is a question of being unable to communicate on your part.

I don't have time to stay behind the people who fly with their finger in the c...

Perfect. you can request the site administrator to close your account. So you and we happy. I unfortunately can't do it, even if I'd like to.. .

 

[re_solidworks]

Bye to all,
I always need to replace a set with a part in the drawing.
I'll spend better.
I have a 2d design connected with 3d of a set. for reasons of simplicity except this together as part and gate or renounce the axieme.when I go to open the drawing I see only empty rectangles. I tried to change the suffix (type) of the part file from .sldprt to sldasm.... I put the same name as the previous witness, but... Nothing to do.
Does anyone have any ideas or do you know any tricks? ?
thank you so much and good work to all

esatb

It should not be done, the table continues to point to the aid and not finding the reference makes the rectangles empty.
if you go to replace the references will no longer exist the distinct because a standard part cannot generate it.
lose the history of the assieme

ah, yes.? ?
even after three years do you have to show up?? :
but before losing energy on these things would not it be better to answer the question made? ?
Thank you.

It'll be 3 years, but the only messages you have are these four, no one has ever seen you around here.

Which one can answer please? ?

if you read the rules says:
8) up - the practice of responding to messages to get them back to the top of the list (see up!) is to be considered prohibited. a forum is not a chat, you need patience to get answers.and this is an infringement.

I asked the question thinking of participating in a forum of specialists, I never thought of dealing with arrogant and bullying.
I don't have time to stay behind the people who fly with their finger in the c...

in a forum a user responds to a bull if he wants, there is no obligation. if you want to be able to claim certain answers there is the subscription offered by retailers.

the question arises: Why do I have to spend time helping someone who doesn't spend a minute in need to read the forum rules?
from your second answer, I think it's all gone by.
I kindly ask you to read the rules and behave in the future, of people who will help you there is a lot even if in this period many are on vacation.
qui the General Rules of the Forum and qui the regulation of the solidworks section.

 

[Mike1967]

ah, yes.? ?
even after three years do you have to show up?? :
but before losing energy on these things would not it be better to answer the question made? ?
Thank you.

Yes, I agree with you... but if you had spent 5 minutes of your precious time you would have found the answer both in the forum (wonderful forum) and in the help of solidworks.:mixed:
Good summer.... .

(from below the umbrella is relaxing read the forum):biggrin:

 

[esatb]

Good morning mike 1967,
Thank you for the answer.
Could you please give me a precise answer as you do, since in my company did not install the Solid Works Help (we work with sw2010), and I do not have much time to look for in the forum? ?
together with me will thank you 10 other designers who do not know how to replace an axieme with a part (always in the drawing).
Thank you very much in advance and good holidays. .

 

[flfn]

The answer to your question cannot be answered.

because you lose all the limits of the quotas of the views and more.... .

greetings

 

[re_solidworks]

Good morning mike 1967,
Thank you for the answer.
Could you please give me a precise answer as you do, since in my company did not install the Solid Works Help (we work with sw2010), and I do not have much time to look for in the forum? ?
together with me will thank you 10 other designers who do not know how to replace an axieme with a part (always in the drawing).
Thank you very much in advance and good holidays. .

if you want to have a part in the table you have to:

1) modeling the axieme
2) save him as part
3) perform the table of this part.

to have the distinct materials you will need to insert the welding function and recompile all hand-prints and you will lose the association between together and part.
Believe me is not the correct approach to use solidworks. in inventor would be different because you can use the "derive" function and you can derive an asm in one part.

another method could be this:

1) create your own set (a)
2) Create a communication set (b) (you don't have to delete)
3) create a blank part to insert it into this together and connect it with coincidence origin
4) also insert the axieme a into the axieme b and connect it with coincidence origin
5) go to contextual change of part
6) with the joint command captures the components of the axieme a.

This method is parametric and in case of modification of some components, remains the problem of the separate.
Keep in mind that it is more difficult to manage a "heavy" multibody part rather than a heavy set with the necessary lightening procedures.


Now:

I made the first step on behalf of the forum. I don't have time to lose, this week I had to be on vacation and instead I'm working for an unexpected.
the forum is a place of mutual enrichment and it is wrong to use it as a help desk.
all members of this forum have benefited from the advice of others over time (I first), you must have a collaborative attitude, in this way you will have exhaustive and timely answers.

Good day

 

[re_solidworks]

...... since my company did not install the Solid Works Help (we work with sw2010). ......

This is wrong, tell your bosses what you need, or are they afraid you learn to use the software?

 

[re_solidworks]

.....(from under the umbrella is relaxing read the forum):biggrin:

You could at least get a little bit of attention to your colleagues who are working.

 

[esatb]

thanks to all those who have put their time at the disposal of my problem.I would like to assure you that I did not respond to the messages in order to return to the top, but simply not to my knowledge of the rules of the forum.
I apologize to everyone that they have been offended by my behavior (following my ignorance towards the rules of the forum) and in the meantime I invite all those who have intervened inappropriately and that in a certain way they have "forced" me to use their language, to be more cautious and tolerant even towards some "abnormal" intervention like mine.
if it is possible to close these discussions and return to the point:
Attached I have inserted a fan (axieme + his corresponding design) that sends me my supplier.
I don't need "the story" of this fan, because I simply have to use it in my colder, so I'd better save it as part (even less weight) (see the attached part).
On the other hand I would like to make a simple design to insert it into the sap(system wants a 3d and a 2d), without the distinct, but only two-three main quotas.
to not begin drawing from head, I asked if I could use the design provided by my supplier simply by replacing the 3719244 axieme with part 3719244? ?
Thank you very much

 

[Mike1967]

Good morning mike 1967,
Thank you for the answer.
Could you please give me a precise answer as you do, since in my company did not install the Solid Works Help (we work with sw2010), and I do not have much time to look for in the forum? ?
together with me will thank you 10 other designers who do not know how to replace an axieme with a part (always in the drawing).
Thank you very much in advance and good holidays. .

I thank you for the explanation you have given, but I remain basic reading certain things: the guide of solidworks is visible to all around the world by chicchessia:
http://help.solidworks.com/2010/ita...ks/legacyhelp/sldworks/overview/startpage.htm

 

[re_solidworks]

thanks to all those who have put their time at the disposal of my problem.I would like to assure you that I did not respond to the messages in order to return to the top, but simply not to my knowledge of the rules of the forum.
I apologize to everyone that they have been offended by my behavior (following my ignorance towards the rules of the forum) and in the meantime I invite all those who have intervened inappropriately and that in a certain way they have "forced" me to use their language, to be more cautious and tolerant even towards some "abnormal" intervention like mine.
if it is possible to close these discussions and return to the point:
Attached I have inserted a fan (axieme + his corresponding design) that sends me my supplier.
I don't need "the story" of this fan, because I simply have to use it in my colder, so I'd better save it as part (even less weight) (see the attached part).
On the other hand I would like to make a simple design to insert it into the sap(system wants a 3d and a 2d), without the distinct, but only two-three main quotas.
to not begin drawing from head, I asked if I could use the design provided by my supplier simply by replacing the 3719244 axieme with part 3719244? ?
Thank you very much

Hi.

I can't see anything, to send a set you should use the function pack and go, they also serve the parts otherwise the axieme is an empty container.

In this case you can use the first procedure I have indicated to you, if you only need it for bulking purposes it is fine anyway.
the table fails to the new part that you saved, however, as if you change the references of the table together to part jump all the quotas and all the notes attached.
do not think about the table of solidworks like a 2d, it is actually the model on white background and positioned as from the orientation of the view, but it is still 3d objects.

 

[re_solidworks]

I thank you for the explanation you have given, but I remain basic reading certain things: the guide of solidworks is visible to all around the world by chicchessia:
http://help.solidworks.com/2010/ita...ks/legacyhelp/sldworks/overview/startpage.htm

I had thought about it myself, but not everyone has internet connection at work, in several companies I know have a dedicated network with pcs dedidcati, often close to the desk of the boss

Now I start working that is better... .