sformo

[kionn]

Bye to all,
I have another problem, I have to create a sform (the red part of the photo)
I also attached the step, I can't always make mistakes,
How can I do that?

 

[Preparation-H]

Bye to all,
I have another problem, I have to create a sform (the red part of the photo)
I also attached the step, I can't always make mistakes,
How can I do that?

I don't want the problem in that connection at the top. . Can't you take it off and try to disfigure again?
also what angle should the sform have?

Hi.
p-h

 

[3dxx]

If you remove that connection, I'll break it.

 

[innocente]

Hi.
I fully agree with the advice of all, remove the fittings, at most you can use the command "remove" to eliminate them and if, just don't want to remove them, you can bypass the problem "by doing the deform" with a sweep :biggrin: and then solidifying it.
I hope I've been helpful. :finger:

 

[kionn]

I can't...
then I have to make a sform of (1o 2) degrees of the upper part but it should not start in the edge the sform but of (1 or 2 mm) more on the edge. . .
I don't know where to start...

 

[innocente]

do a sweep that with a command do everything...:biggrin:
- Yeah.
-select the contour (before a edge then hold down shift to select it all)
-references:normal to projection (choose the plan you would use for the deform)
-options: constant section
-sketch (inside):make the form that interests you
-select as solid (the cube dispenser)
- remove material (the square with an oblique line)
- finished! :finger:
Hi.

 

[maxopus]

I can't...
then I have to make a sform of (1o 2) degrees of the upper part but it should not start in the edge the sform but of (1 or 2 mm) more on the edge. . .
I don't know where to start...

Here's the sform.
I only eliminated the fitting, created a plane about 1.5 mm from the edge and made the sform.
See if that's what you wanted.
I did it with the wf4, what version do you use?

 

[kionn]

Excuse me and my ignorance in this matter. .
What kind of sweep I have to do. .
protruding
thin protrusion
Cut. . .
...

 

[kionn]

I can't open it. I have a wf3.

 

[Preparation-H]

I can't open it. I have a wf3.

with the 3 you cannot delete the connection if the original file is neutral (.step for example).
more than a sweep you should use the variable section sweep.


Hi.
p-h

 

[maxopus]

I can't open it. I have a wf3.

Here's the step.

 

[kionn]

I just want to know how to do it.
because I must definitely see the difference between 1...2°. .
height 1 mm or 1.5 mm...
How do I do with wf3
I can't do this:

 

[innocente]

Here is the piece made with the wf3.

for preparation-h, if the math of the .step (as in this case) is not complex the remove command works with the wf3, only that you have to eliminate also the central connection, otherwise as you say it does not.

 

[kionn]

Thank you very much. .
Now I'll put some on this command. .

 

[mali_fx]

I press that I didn't look at the 3d cmq I tell you that by doing a general speech, with the sweep you always solve the problem and you can always disfigurement with the sform you are very limited so don't stare too much on the sform! (pro sform and is very cool about certain things)
with the sweep you can also unform starting tangent at the radius with the sform you can almost never unless the piece is ''banalissimo'!
personally I often find the need to start tangent at the radius and disform as you can not always restore the rays automatically.