tilted hole on fitting

[Geppetto82]

Hello, everyone.
I'm trying, but I can't.... .
How do I run a tilted hole that, starting from the 3rd floor, I go to break the milling 10?
allego part performed with sw11 sp1.0 and relative image.
thanks to all
greetings
geppetto 82

 

[cacciatorino]

Hello, everyone.
I'm trying, but I can't.... .
How do I run a tilted hole that, starting from the 3rd floor, I go to break the milling 10?
allego part performed with sw11 sp1.0 and relative image.
thanks to all
greetings
geppetto 82

I'd do this.

1) tangent plan to the connection

2) floor parallel to the floor of which 1 with external offset

3) hole from the top of which 2 to the pocket.

I think I didn't understand your problem well, but you'd already come by yourself... .

 

[Oldwarper]

Plan 3 is tangent to the chord, if I see well.
select the plan and go with guided drilling.. .

too trivial...? ? ?

Maybe he didn't understand what the problem is, too...

 

[Geppetto82]

Hello hunter.
In fact I did as you wrote, even.
but by doing the hole, of course, it is perpendicular to the floor and does not go to break the pocket.
I have to tilt I do not know how the starting plan of the hole, so that the hole will be tilted and will go to sink the pocket....
you don't have sw?

 

[cacciatorino]

Hello hunter.
In fact I did as you wrote, even.
but by doing the hole, of course, it is perpendicular to the floor and does not go to break the pocket.
I have to tilt I do not know how the starting plan of the hole, so that the hole will be tilted and will go to sink the pocket....
you don't have sw?

So, swx I have it, but it's 2010 and then it's hard to turn it on! :tongue:

However if I understand, try to trace a sketch line from the center of the pocket to the center of the fitting, and then use it to create your starting plan, perpendicular to the segment and tangent to the chord. I hope I understood your porblem.

 

[Geppetto82]

I probably can't explain.... .
if they place me frontally to the piece you notice that the pocket is moved compared to the hole (see image).
the plane 3 (the starting plane of the hole) must be inclined not tangent to the connection!
Is it a little clearer now?
Sorry for the little clarity I'm telling you about the problem....but if you open the part you understand well!
If you don't have sw I'll send you an iges or a step?

 

[cacciatorino]

I probably can't explain.... .
if they place me frontally to the piece you notice that the pocket is moved compared to the hole (see image).
the plane 3 (the starting plane of the hole) must be inclined not tangent to the connection!
Is it a little clearer now?
Sorry for the little clarity I'm telling you about the problem....but if you open the part you understand well!
If you don't have sw I'll send you an iges or a step?

I don't understand yet, but if you draw a sketch on the front face of your piece with the axis of what will be your hole (with all the auxiliary geometries that will be useful to you) and then create a perpendicular plan to that axis and parts from that to drill?

 

[Oldwarper]

I don't understand yet, but if you draw a sketch on the front face of your piece with the axis of what will be your hole (with all the auxiliary geometries that will be useful to you) and then create a perpendicular plan to that axis and parts from that to drill?

Maybe I get it.

geppetto, do as it says hunting, take a point on the bribe line of the plan with the fitting and another "dovetipare" on the pocket, draw a line with "schizzo 3d" and make a perpendicular plan to the line at the point of the chord. from that plan you make the hole.

attention: you should do it from an offset plan of that obtained otherwise the hole will have a start from a plan that secretes the solid and therefore can be incomplete. Alternatively, you may prolong a "tot" the pass line to the point on the connection and the pnto we will extremize (which will now be outside the surface of the connection) using the guided drilling.

hth.

 

[Mike1967]

How? ? ? ?

I also attach the file...

 

[Mike1967]

How? ? ? ?

I also attach the file...

Sorry, the image I had attached had some problem with
display. . .

 

[Geppetto82]

Mike... .
Do you remember what I wrote you a few days ago?? ? ?
I confirm! ! !
Anyway I was approaching the solution using 3d sketch, I don't have much familiarity with this command.... .
I have to do some tutorials.. . .
Now I try... .
Thanks as always!

 

[Geppetto82]

I realized why I couldn't with 3d sketch....
Clear!! !
I learned something new....
banal for many but not for me!

 

[Mike1967]

Mike... .
Do you remember what I wrote you a few days ago?? ? ?
I confirm! ! !
Anyway I was approaching the solution using 3d sketch, I don't have much familiarity with this command.... .
I have to do some tutorials.. . .
Now I try... .
Thanks as always!

grande !!

I realized why I couldn't with 3d sketch....
Clear!! !
I learned something new....
banal for many but not for me!

as in all things, only with the practice and exchange of experiences between
users/colleges/friends accelerate learning...:finger: