challenge cam to comparison

[RS4]

hi, I turn you off as I did in topcam, I defintio in toptool, which and the tool database of topcam, the tool defining the ingombs and the radius of the tool included the stamp of the stem not to heel and then I applied the finishing cycle in subsqadro with a z step of 0.2 without limiting for profiles. I've just put a limit on my own to stop on the floor.

in the coming days I send you the paths on the pieces you have already made

we did the same things upper limit; top surface grey beginning underscore in my case, bottom surface grey discrete with constant past 0.2mm

I understand:

 

[corsaro33]

Featurecam present,
strategy used finish level z
with the possibility to choose height ridge or step in z.

greetings possible to the next

 

[Stefano Vezzani]

hi to all I have made some paths on the backward tests I attach you some pictures in the file
test 1 I have made a 3d roughing with a torica radius 4 the roughing of topsolid previews that depending on the zones I can make strategy of different paths type to prirale where I have zones closed type pocket to successive contours where I have profiles to open pocket and zig zag where I have zones open type sanding (in top there are 5 kinds of different cycles of roughing and shooting with so many modalities) moreover
in the test file I made an isoparaetric finish with a 10 mm semi-spherical by selecting all faces

 

[Stefano Vezzani]

for the subsquadro cycle I have not selected anything I only gave the beginning z quota and the end z quota

 

[Stefano Vezzani]

we did the same things upper limit; top surface grey beginning underscore in my case, bottom surface grey discrete with constant past 0.2mm

I understand:

for the subframe I only selected the odds z of the working range

 

[RS4]

for the subframe I only selected the odds z of the working range

but did I optimize it for the z-levels? ? ? ?

what type of processing tolerance you used 0.02mm

greetings

♪

 

[RS4]

for the subsquadro cycle I have not selected anything I only gave the beginning z quota and the end z quota

same thing made by me:

 

[Dadino]

finishing process for complete parallel past shooting on edge, without selecting containment edges and tolerance definition at 0.01mm calculation time 14 seconds

 

[RS4]

Good morning

a little late :biggrin: anyway welcome ..... and thank you for your interest

 

[Dior]

Hello paolo.m I see from your challenge with rs4 that you are very prepared with caia machining, using this program I always have difficulty with cams!!! Would you like to indicate a manual also not necessarily in Italian that treats the cam environments??? help me help me

 

[AlbFallo84]

hi to all I have made some paths on the backward tests I attach you some pictures in the file
test 1 I have made a 3d roughing with a torica radius 4 the roughing of topsolid previews that depending on the zones I can make strategy of different paths type to prirale where I have zones closed type pocket to successive contours where I have profiles to open pocket and zig zag where I have zones open type sanding (in top there are 5 kinds of different cycles of roughing and shooting with so many modalities) moreover
in the test file I made an isoparaetric finish with a 10 mm semi-spherical by selecting all facesView attachment 21405
View attachment 21406

Good morning, I've been using topsolid recently. I've seen you're hard and I'd like to ask you some info about the roughing. I'm making a 4 radial axle roughing with a d25. I would like to resume areas where the d25 does not enter, I repeat the roughing 4 radial axes with a d12, but topsolid does not detect the rough of the d25 by making me the complete cycle: As if the crude had not been worked by the d25. I used hypermills and there the logic of roughing was different, here I can't figure out how I do the ripping, can you help me? Thank you very much