large drawings

[strudeldemele]

.........instead, if you can pass your configurations or post the tips and ratings they gave you, I think you'd do a great pleasure to many
Thank you.

 

[320i S]

.........instead, if you can pass your configurations or post the tips and ratings they gave you, I think you'd do a great pleasure to many
Thank you.

Unfortunately I can't do this for corporate agreements....but I guarantee that by analyzing the cases well, you can improve a lot.

 

[320i S]

hi 320i s
very well, the same I had deducted..... workstations with i7 fast go much better than xeon (as well as for a performance xeon prices rise too much), anyway I see that if you do not render the most "stressed" part is the processor that must continue to write (if there is the server worse yet)
the problem is that, who does mounts, details etc. can solve in various ways (no reference, reimport parts etc.); My problem is that developing projects from zero of industrial lines occupying a shed, a small set has about 5000 pcs, if I have to work without references or other tools of the 3d, then it is better if I return to autocad mechanical, I need to draw so that I can overturn the project in a short time and with few steps, and with the tools that give me until now I have failed.

processor side, it also depends on what you go to do, I also have the simulation license and also exploits the multicores, so a square of the main necessities is found.

for specific cases such as planting, there are the appropriate modules, they are an additional cost, but they are made specifically to streamline management complications.
external references, can be bypassed in many ways, for example a "sympathetic" system I learned it with pro-e/creo, i.e. to make a skeleton (a part with zero weight and simple mathematicians that simulate the layout), that I insert it in the various subassies and constraint its components, helping me with the skeleton, if I have to update something high level, I modify the skeleton all

 

[MassiVonWeizen]

references can be blocked, which is very different to interrupt.
the block of references can be reactivated.
http://help.solidworks.com/2019/ita..._locking_and_breaking_external_references.htm

 

[MassiVonWeizen]

did you try, as I suggested, to spread the views on multiple sheets?

 

[strudeldemele]

Hi.
I tried, a bit improves but the time recovered you lose it to pass between the sheets, recompose etc....
Instead, I noticed that the major problems are in the refresh of the views as if it should always recalculate the display thicknesses of the lines.....know if you can exclude the thickness lines in the display of the tables?
Thank you.
Good weekend

 

[MassiVonWeizen]

try to block the location of the views.
for the lines you can put the views in shaded mode without borders in the views where you do not work.
it would also be to exclude edge highlighting in system selection options during selection, but it becomes ostico quotare; you can still try

 

[drake]

because the problem of the table is a problem that is still open, I ask you if you have been able to test any differences with the latest versions of sw. if you have also installed the 2020 version, have you tried if really there is a real increase in performance in the table? I was seeing the novelties of the version and it seems that with the latter they worked on this in a deep way. it would be interesting to know if it really is. When I started a new discussion about the real differences in the versions, but the discussion didn't go as I hoped. reading the sensations and experiences of real users of the software, is the best way to assess whether it is worth updating or not.

 

[Fabius3D]

Good morning. I put in here because I do not find a precise post to solve my problem and I do not want to start a new post to minchiam!
solidworks software 2018
I have a big set, about 4-5000 parts. is divided into three separate macro-solids. 2 of these are close to each other, while a 3rd is distant and when I zoom to fit both are tiny (fig.2). can I make sure you can see everything not as far as it is near?(fig.1) I attach 2 photos to be clearer. .
Thank you.

 

[MassiVonWeizen]

no non puoi.

 

[strudeldemele]

Hi.
Unfortunately the problem of the boards is the regeneration of the lines and the view in phase of zoom and movement in the design.... everything I tried improves a little but loses it to recompose the table correctly
I go back to the tecnigraph and the china!!! ! ! !