series in two opposite directions (prow w2)

[PiDezz]

hi, I am new to the forum and so I greet everyone and thank early who will help me.
I would like to point out that I have little familiarity with proes as I use almost only the 2d (medusa4 adv) and therefore my problem could be a banality.
I have to do a simple pulley with 7 gorges, my problem is due to the fact that the departure I have on that central one.
Now, made the central throat quarry in revolution with the throat center positioned on a floor, I have to make a series for the other gorges, 3 on one side and 3 on the other.
I go to give the serial comendo, select direction, then the plan that goes to the center throat, type 4 as number of gorges (having three besides the original in one direction), then repeat all in the opposite direction.
to see everything ok, if I open the series, inside I will not have 7 features, but 16 as in the direction 2 I made 4 copies of the 4 features that I have in the direction 1.
doing some tests with holes on a plate, selecting perpendicular planes for the departure of the two directions, I understood the reason... .
My question at this point is, is there a way to make the series that I need without any copies of features going to overlap?
obviously keeping the start in the feature of center.

Thank you.

 

[maxopus]

If there is no confidentiality problem, could you post the file?

 

[SweptBlend]

If I understand what you want to do, the answer is no.
you do not want to make a series in 2 directions, but a series in 1 direction,
from 2 sides, something not possible, because the series is born as an increase from the previous position.
So either models the first throat, and then the series you do it all on one side,
or you have to copy...

 

[PiDezz]

If there is no confidentiality problem, could you post the file?

mmm, image prepared for benign, but I don't know how to post it without loading it on some site....

however sweptblend summarized perfectly:
"a series in 1 direction, from 2 sides"

I was afraid you couldn't have found anything on the manuals:frown:

Thanks the same.

 

[maxopus]

How much do you give me?

 

[re_solidworks]

if for second direction select the same edge and check the same distance does not flee?

 

[PiDezz]

x maxopus

Is a virtual drink enough?


x re_solidworks

you can not make a sound of a feature that has already been used for another series.
At least, it doesn't even highlight the command icon, so I don't think you can....

 

[maxopus]

if for second direction select the same edge and check the same distance does not flee?

Come on, you get screwed by a swx user. :biggrin::biggrin:
it is so, indicated as the second direction the same utlized direction for the first.
as the step used for the first multiplied by the number of holes (if in the first direction you had 5 copies in step 50, in the second you will indicate 2 copies in step 250).
be careful that you have to exclude the last hole of the second direction, otherwise there is one more, rightly.

 

[maxopus]

If I understand what you want to do, the answer is no.
you do not want to make a series in 2 directions, but a series in 1 direction,
from 2 sides, something not possible, because the series is born as an increase from the previous position.
So either models the first throat, and then the series you do it all on one side,
or you have to copy...

x maxopus

Is a virtual drink enough?


x re_solidworks

you can not make a sound of a feature that has already been used for another series.
At least, it doesn't even highlight the command icon, so I don't think you can....

Do I have to post the film or just the previous explanation?

 

[Preparation-H]

Come on, you get screwed by a swx user. :biggrin::biggrin:
it is so, indicated as the second direction the same utlized direction for the first.
as the step used for the first multiplied by the number of holes (if in the first direction you had 5 copies in step 50, in the second you will indicate 2 copies in step 250).
be careful that you have to exclude the last hole of the second direction, otherwise there is one more, rightly.

exactly, it works just like that... :finger: :biggrin:

Hi.
p-h

 

[PiDezz]

Thank you, try and work.
what was very simple to do, just think about it:wink:

One last stupid question.
since it is not possible to erase only the last one, because in that case it erases everything, the only way is to hide it by putting it in "hide", jester^

 

[maxopus]

no, when you realize the series, with the ctrl key pressed, click with the left button on the last black ball of the same which becomes white and excludes the element from the series.

 

[PiDezz]

Thank you very much.

♪

 

[matteoso]

I'm sorry, I'm probably going to say something.
once made the 1st series of 3 gorges, can't you mirror the series just obtained?

 

[maxopus]

I'm sorry, I'm probably going to say something.
once made the 1st series of 3 gorges, can't you mirror the series just obtained?

Yes... if you are not located right on the middle floor with the feature.